- 您現在的位置：買賣IC網 > PDF目錄1922 > FT2232D-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS DUAL UART/FIFO 48-LQFP PDF資料下載
參數資料
| 型號： | FT2232D-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 47/61頁 |
| 文件大小： | 0K |
| 描述： | IC USB FS DUAL UART/FIFO 48-LQFP |
| 產品培訓模塊： | USB Introduction |
| 標準包裝： | 1 |
| 系列： | USBmadeEZ-FIFO，F(xiàn)T-X，X-Chip |
| 特點： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道數： | 2，DUART |
| FIFO's： | 384 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 4.35 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1030-ND - MOD USB HS FT2232H EVAL 813-1009-ND - MODULE USB-TO-FPGA TOOL W/MANUAL 813-1001-ND - MODULE USB ADAPTR FOR FT2232D LP 813-1000-ND - MODULE USB ADAPTER FOR FT2232D |
| 其它名稱： | 768-1010-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
Copyright 2010 Future Technology Devices International Limited
51
Document No.: FT_000173
FT2232D DUAL USB TO SERIAL UART
/FIFO IC Datasheet
Version 2.05
Clearance No.: FTDI# 127
Figure 8.17 Fast Opto-Isolated Serial Interface Example
In the example shown in figure 8.18 two Agilent HCPL-2430 (see the semiconductor section at
www.agilent.com) high speed opto-couplers are used to optically isolate an external device which
interfaced to USB using the FT2232D. In this example VCC5V is the supply for the FT2232D (bus or self
powered), and VCCE is the supply to the external device.
Care must be taken with the voltage used to power the photoLEDs. It should be the same supply that
the I/Os are driving to, or the LEDs may be permanently on. Limiting resistors should be fitted in the
lines that drive the diodes. The outputs of the opto-couplers are open-collector and so need a pullup
resistor.
Testing
Fast serial mode has been tested using an Scenix (Ubicom), SX28 microcontroller (see
www.ubicom.com) which was configured in loopback mode. This was done both with, and without HP
HCPL-2430 opto-isolators in place. The isolators add a considerable delay to the turnaround time seen by
the micro. This was close to 100 nS with the high speed HCPL-2430 device. This is the combined delay of
the clock signal from the microcontroller going through an opto-coupler to the chip, and the data from
the FT2232D chip going through the other opto-coupler back to the microcontroller.
相關PDF資料 |
PDF描述 |
|---|---|
| FT2232HQ-REEL | IC USB HS DUAL UART/FIFO 64-QFN |
| FT232BL-REEL | IC USB FS SERIAL UART 32-LQFP |
| FT232HL-REEL | IC HS USB TO UART/FIFO 48LQFP |
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
| FT2232H | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART |
| FT2232H MINI MODULE | 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232H_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
| FT2232H_12 | 制造商:FTDI 制造商全稱:FTDI 功能描述:Dual High Speed USB to Multipurpose UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。