參數資料
型號: HYB 39S128160CT
廠商: SIEMENS AG
英文描述: 128-Mbit(4banks × 2MBit × 16) Synchronous DRAM(128M(4列 × 2M位 × 16)同步動態RAM)
中文描述: 128兆位(4banks × 2Mbit的× 16)同步DRAM(128M的(4列× 2位× 16)同步動態RAM)的
文件頁數: 12/42頁
文件大?。?/td> 280K
代理商: HYB 39S128160CT
HYB 39S128400/800/160CT(L)
128-MBit Synchronous DRAM
Data Book
12
1.00
done even before the previous burst ends. The interrupt operation at every clock cycle is supported.
When the previous burst is interrupted, the remaining addresses are overridden by the new address
with the full burst length. An interrupt which accompanies an operation change from a read to a write
is possible by exploiting DQM to avoid bus contention.
When two or more banks are activated sequentially, interleaved bank read or write operations are
possible. With the programmed burst length, alternate access and precharge operations on two or
more banks can realize fast serial data access modes among many different pages. Once two or
more banks are activated, column to column interleave operation can be performed between
different pages.
Refresh Mode
SDRAM has two refresh modes, Auto Refresh and Self Refresh. Auto Refresh is similar to the CAS
-before-RAS refresh of conventional DRAMs. All of banks must be precharged before applying any
refresh mode. An on-chip address counter increments the word and the bank addresses and no
bank information is required for both refresh modes.
The chip enters the Auto Refresh mode, when RAS and CAS are held low and CKE and WE are
held high at a clock timing. The mode restores word line after the refresh and no external precharge
command is necessary. A minimum
t
RC
time is required between two automatic refreshes in a burst
refresh mode. The same rule applies to any access command after the automatic refresh operation.
The chip has an on-chip timer and the Self Refresh mode is available. It enters the mode when RAS,
CAS, and CKE are low and WE is high at a clock timing. All of external control signals including the
clock are disabled. Returning CKE to high enables the clock and initiates the refresh exit operation.
After the exit command, at least one
t
RC
delay is required prior to any access command.
Burst Length and Sequence
Burst
Length
Starting
Address
(A2 A1 A0)
Sequential Burst
Addressing
(decimal)
Interleave Burst
Addressing
(decimal)
2
xx0
xx1
0, 1
1, 0
0, 1
1, 0
4
x00
x01
x10
x11
0, 1, 2, 3
1, 2, 3, 0
2, 3, 0, 1
3, 0, 1, 2
0, 1, 2, 3
1, 0, 3, 2
2, 3, 0, 1
3, 2, 1, 0
8
000
001
010
011
100
101
110
111
0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 0
2 3 4 5 6 7 0 1
3 4 5 6 7 0 1 2
4 5 6 7 0 1 2 3
5 6 7 0 1 2 3 4
6 7 0 1 2 3 4 5
7 0 1 2 3 4 5 6
0 1 2 3 4 5 6 7
1 0 3 2 5 4 7 6
2 3 0 1 6 7 4 5
3 2 1 0 7 6 5 4
4 5 6 7 0 1 2 3
5 4 7 6 1 0 3 2
6 7 4 5 2 3 0 1
7 6 5 4 3 2 1 0
相關PDF資料
PDF描述
HYB 39S128400CT 128-Mbit(4banks × 8MBit × 4) Synchronous DRAM(128M(4列 × 8M位 × 4)同步動態RAM)
HYB 39S128800CT 128-Mbit(4banks × 4MBit × 8) Synchronous DRAM(128M(4列 × 4M位 × 8)同步動態RAM)
HYB 39S16160CT-5.5 1M × 16-Mbit Synchronous DRAM for High-Speed Graphics Applications(16M位(1M × 16)同步動態RAM(用于高速圖形場合))
HYB 39S16160CT-6 1M × 16-Mbit Synchronous DRAM for High-Speed Graphics Applications(16M位(1M × 16)同步動態RAM(用于高速圖形場合))
HYB 39S16160CT-7 1M × 16-Mbit Synchronous DRAM for High-Speed Graphics Applications(16M位(1M × 16)同步動態RAM(用于高速圖形場合))
相關代理商/技術參數
參數描述
HYB39S128160CT-7 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128-MBit Synchronous DRAM
HYB39S128160CT-7.5 制造商:Infineon Technologies AG 功能描述:SDRAM, 8M x 16, 54 Pin, Plastic, TSOP
HYB39S128160CT-75 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128-MBit Synchronous DRAM
HYB39S128160CT-8 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128-MBit Synchronous DRAM
HYB39S128160CTL-7.5 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128-MBit Synchronous DRAM