- 您現在的位置：買賣IC網 > PDF目錄383155 > ISL6540A (Intersil Corporation) Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability PDF資料下載
參數資料
| 型號： | ISL6540A |
| 廠商： | Intersil Corporation |
| 英文描述： | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| 中文描述： | 單相降壓PWM控制器，帶有集成的高速MOSFET驅動器和預偏置負載能力 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 430K |
| 代理商： | ISL6540A |
9
FN6288.2
March 12, 2007
Functional Pin Description
VSEN+ (Pin 1)
This pin provides differential remote sense for the ISL6540A.
It is the positive input of a standard instrumentation amplifier
topology with unity gain, and should connect to the positive
rail of the load/processor. The voltage at this pin should be
set equal to the internal system reference voltage (0.591V
typical.)
VSEN- (Pin 2)
This pin provides differential remote sense for the regulator.
It is the negative input of the instrumentation amplifier, and
should connect to the negative rail of the load/processor.
Typically 6
μ
A is sourced from this pin. The output of the
remote sense buffer is disabled (High Impedance) by pulling
VSEN- to VCC.
REFOUT (Pin 3)
This pin connects to the unmargined system reference
through an internal buffer. It has a 19mA drive capability with
an output common mode range of GND to VCC. The
REFOUT buffer requires at least 1
μ
F of capacitive loading to
be stable. This pin should not be left floating.
REFIN (Pin 4)
When the external reference pin (REFIN) is NOT within
~1.8V of VCC, the REFIN pin is used as the system
reference instead of the internal 0.591V reference. The
recommended REFIN input voltage range is ~68mV to
VCC - 1.8V.
SS (Pin 5)
This pin provides softstart functionality for the ISL6540A. A
capacitor connected to ground along with the internal 37μA
Operational Transconductance Amplifier (OTA), sets the
soft-start interval of the converter. This pin is directly
connected to the non-inverting input of the error amplifier. To
prevent noise injection into the error amplifier the SS
capacitor should be located next to the SS and GND pins.
OFS+ (Pin 6)
This pin sets the positive margining offset voltage. Resistors
should be connected to GND (R
OFS+
) and OFS- (R
MARG
)
from this pin. With MAR_CTRL logic low, the internal 0.591V
reference is developed at the OFS+ pin across resistor
R
OFS+
. The voltage on OFS+ is driven from OFS- through
R
MARG
. The resulting voltage differential between OFS+
and OFS- is divided by 5 and imposed on the system
reference. The maximum designed offset of 1V between
OFS+ and OFS- pins translates to a 200mV offset.
OFS- (Pin 7)
This pin sets the negative margining offset voltage. Resistors
should be connected to GND (R
OFS-
) and OFS+ (R
MARG
)
from this pin. With MAR_CTRL logic low, the internal 0.591V
reference is developed at the OFS- pin across resistor
R
OFS-
. The voltage on OFS- is driven from OFS+ through
R
MARG
. The resulting voltage differential between OFS+
and OFS- is divided by 5 and imposed on the system
reference. The maximum designed offset of -1V between
OFS+ and OFS- pins translates to a -200mV offset of the
system reference.
VCC (Pin 8, Analog Circuit Bias)
This pin provides power for the ISL6540A analog circuitry.
The pin should be connected to a 2.9V to 5.5V bias through
an RC filter from PVCC to prevent noise injection into the
analog circuitry. This pin can be powered off the internal or
external linear regulator options.
MARCTRL (Pin 9)
The MARCTRL pin controls margining function, a logic high
enables positive margining, a logic low sets negative
margining, a high impedance disables margining.
PG_DLY (Pin 10)
Provides the ability to delay the output of the PGOOD
assertion by connecting a capacitor from this pin to GND. A
0.1
μ
F capacitor produces approximately a 7ms delay.
PGOOD (Pin 11)
Provides an open drain Power Good signal when the output
is within 9% of nominal output regulation point with 6%
hysteresis (15%/9%), and after soft-start is complete.
PGOOD monitors the VMON pin.
EN (Pin 12)
This pin is compared with an internal 0.50V reference and
enables the soft-start cycle. This pin also can be used for
voltage monitoring. A 10
μ
A current source to GND is active
while the part is disabled, and is inactive when the part is
enabled. This provides functionality for programmable
hysteresis when the EN pin is used for voltage monitoring.
VFF (Pin 13)
The voltage at this pin is used for input voltage feed forward
compensation and sets the internal oscillator ramp peak to
peak amplitude at 0.16 * VFF. An external RC filter may be
required at this pin in noisy input environments. The
minimum recommended VFF voltage is 2.97V.
I
PG_LOW
PGOOD Low Output Voltage
I
PGOOD
= 5mA
-
-
0.150
V
I
PG_MAX
Maximum Sinking Current
V
PGOOD
= 0.8V
23
-
-
mA
V
PG_MAX
Maximum Open Drain Voltage
VCC = 3.3V
-
6
-
V
Electrical Specifications
Recommended Operating Conditions, Unless Otherwise Noted
(Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
ISL6540A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6540ACRZ | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540ACRZA | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540AIRZ | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6540AIRZA | Single-Phase Buck PWM Controller with Integrated High Speed MOSFET Driver and Pre-Biased Load Capability |
| ISL6545 | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6540ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6540ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| ISL6540ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6540ACRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6540AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6540AIRZA | 功能描述:IC REG CTRLR BUCK PWM VM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。