- 您現在的位置：買賣IC網 > PDF目錄373087 > K9F1208R0B (SAMSUNG SEMICONDUCTOR CO. LTD.) TV 99C 97#22D 2#8(TWINAX) SKT PDF資料下載
參數資料
| 型號： | K9F1208R0B |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | TV 99C 97#22D 2#8(TWINAX) SKT |
| 中文描述： | 6400 × 8位NAND閃存 |
| 文件頁數： | 40/45頁 |
| 文件大小： | 1029K |
| 代理商： | K9F1208R0B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁
FLASH MEMORY
40
K9F1208B0B
K9F1208U0B
K9F1208R0B
Preliminary
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to table 4 for specific Status Register definitions. The command register
remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read
cycle, a read command(00h or 50h) should be given before sequential page read cycle.
For Read Status of Multi Plane Program/Erase, the Read Multi-Plane Status command(71h) should be used to find out whether multi-
plane program or erase operation is completed, and whether the program or erase operation is completed successfully. The pass/fail
status data must be checked only in the Ready condition after the completion of Multi-Plane program or erase operation.
Table4. Read Staus Register Definition
NOTE
:
1. I/O 0 describes combined Pass/Fail condition for all planes. If any of the selected multiple pages/blocks fails in Program/
Erase operation, it sets "Fail" flag.
2. The pass/fail status applies only to the corresponding plane.
I/O No.
Status
Definition by 70h Command
Definition by 71h Command
I/O 0
Total Pass/Fail
Pass : "0" Fail : "1"
Pass : "0"
(1)
Fail : "1"
I/O 1
Plane 0 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 2
Plane 1 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 3
Plane 2 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 4
Plane 3 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 5
Reserved
Must be don’t -cared
Must be don’t-cared
I/O 6
Device Operation
Busy : "0" Ready : "1"
Busy : "0" Ready : "1"
I/O 7
Write Protect
Protected : "0" Not Protected : "1"
Protected : "0" Not Protected : "1"
相關PDF資料 |
PDF描述 |
|---|---|
| K9F1208B0B | 64M x 8 Bit NAND Flash Memory |
| K9F1208U0 | 64M x 8 Bit NAND Flash Memory |
| K9F1208U0M-YIB0 | 64M x 8 Bit NAND Flash Memory |
| K9F1208U0M-YCB0 | 64M x 8 Bit NAND Flash Memory |
| K9F1208U0M- | 64M x 8 Bit NAND Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9F1208R0C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:三星公司新版本NAND FLASH |
| K9F1208R0C-J | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY |
| K9F1208R0C-JIB0000 | 制造商:Samsung SDI 功能描述: |
| K9F1208U0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:64M x 8 Bit NAND Flash Memory |
| K9F1208U0A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:64M x 8 Bit , 32M x 16 Bit NAND Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。