- 您現在的位置：買賣IC網 > PDF目錄373089 > K9S1208V0M-SSB0 (SAMSUNG SEMICONDUCTOR CO. LTD.) 64M x 8 Bit SmartMedia Card PDF資料下載
參數資料
| 型號： | K9S1208V0M-SSB0 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 64M x 8 Bit SmartMedia Card |
| 中文描述： | 6400 × 8位SmartMedia卡 |
| 文件頁數： | 29/33頁 |
| 文件大?。?/td> | 491K |
| 代理商： | K9S1208V0M-SSB0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁
K9S1208V0M-SSB0
SmartMedia
TM
29
MULTI-PLANE BLOCK ERASE
Basic concept of Multi-Plane Block Erase operation is identical to that of Multi-Plane Page Program. Up to four blocks, one from each
plane can be simultaneously erased. Standard Block Erase command sequences (Block Erase Setup command followed by three
address cycles) may be repeated up to four times for erasing up to four blocks. Only one block should be selected from each plane.
The Erase Confirm command initiates the actual erasing process. The completion is detected by analyzing R/B pin or Ready/Busy
status (I/O 6). Upon the erase completion, pass/fail status of each block is examined by reading extended pass/fail status(I/O 1
through I/O 4).
Figure 19. Four Block Erase Operation
60h
A
0
~ A
7
& A
9
~ A
25
I/O
0
~
7
R/B
Address
(3 Cycle)
60h
60h
60h
D0h
71h
I/O
Pass
Fail
t
BERS
Address
(3 Cycle)
Address
(3 Cycle)
Address
(3 Cycle)
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to table 2 for specific Status Register definitions. The command register
remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read
cycle, a read command(00h or 50h) should be given before sequential page read cycle.
For Read Status of Multi Plane Program/Erase, the Read Multi-Plane Status command(71h) should be used to find out whether
multi-plane program or erase operation is completed, and whether the program or erase operation is completed successfully. The
pass/fail status data must be checked only in the Ready condition after the completion of Multi-Plane program or erase operation.
I/O No.
Status
Definition by 70h Command
Definition by 71h Command
I/O 0
Total Pass/Fail
Pass : "0" Fail : "1"
Pass : "0"
(1)
Fail : "1"
Pass : "0"
(2)
Fail : "1"
Pass : "0"
(2)
Fail : "1"
Pass : "0"
(2)
Fail : "1"
Pass : "0"
(2)
Fail : "1"
Must be don’t-cared
I/O 1
Plane 0 Pass/Fail
Must be don’t -cared
I/O 2
Plane 1 Pass/Fail
Must be don’t -cared
I/O 3
Plane 2 Pass/Fail
Must be don’t -cared
I/O 4
Plane 3 Pass/Fail
Must be don’t -cared
I/O 5
Reserved
Must be don’t -cared
I/O 6
Device Operation
Busy : "0" Ready : "1"
Busy : "0" Ready : "1"
I/O 7
Write Protect
Protected : "0" Not Protected : "1"
Protected : "0" Not Protected : "1"
Table2. Read Staus Register Definition
NOTE
:
1. I/O 0 describes combined Pass/Fail condition for all planes. If any of the selected multiple pages/blocks fails in Program/
Erase operation, it sets "Fail" flag.
2. The pass/fail status applies only to the corresponding plane.
相關PDF資料 |
PDF描述 |
|---|---|
| K9S1208V0 | 64MB & 128MB SmartMediaTM Card |
| K9D1G08V0M | 64MB & 128MB SmartMediaTM Card |
| K9S6408V0A-SSB0 | 8M x 8 Bit SmartMediaTM Card |
| KA-3020 | 3x2mm SINGLE COLOR SURFACE MOUNT LED LAMPS |
| KA-3020EC | 3x2mm SINGLE COLOR SURFACE MOUNT LED LAMPS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9S2808V0B | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SmartMedia CARD |
| K9S2808V0C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SmartMedia CARD |
| K9S2808V0M | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:16M x 8 Bit SmartMedia Card |
| K9S2808V0M-SSB0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:16M x 8 Bit SmartMedia Card |
| K9S3208V0A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:4M x 8 bit SmartMedia Card |
發布緊急采購，3分鐘左右您將得到回復。