- 您現在的位置：買賣IC網 > PDF目錄2002 > KAD5610P-25Q72 (Intersil)IC ADC 10BIT 250MSPS DUAL 72-QFN PDF資料下載
參數資料
| 型號： | KAD5610P-25Q72 |
| 廠商： | Intersil |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 250MSPS DUAL 72-QFN |
| 產品培訓模塊： | High-Speed Analog-to-Digital Converters |
| 標準包裝： | 1 |
| 系列： | FemtoCharge™ |
| 位數： | 10 |
| 采樣率（每秒）： | 250M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 438mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 72-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 72-QFN（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
14
FN6810.2
September 10, 2009
Theory of Operation
Functional Description
The KAD5610P is based upon a 10-bit, 250MSPS A/D
converter core that utilizes a pipelined successive
approximation architecture (Figure 22). The input voltage is
captured by a Sample-Hold Amplifier (SHA) and converted to
a unit of charge. Proprietary charge-domain techniques are
used to successively compare the input to a series of
reference charges. Decisions made during the successive
approximation operations determine the digital code for each
input value. The converter pipeline requires six samples to
produce a result. Digital error correction is also applied,
resulting in a total latency of seven and one half clock cycles.
This is evident to the user as a latency between the start of a
conversion and the data being available on the digital outputs.
The device contains two A/D converter cores with carefully
matched transfer characteristics. At start-up, each core
performs a self-calibration to minimize gain and offset errors.
The reset pin (RESETN) is initially set high at power-up and
will remain in that state until the calibration is complete. The
clock frequency should remain fixed during this time, and no
SPI communications should be attempted. Recalibration can
be initiated via the SPI port at any time after the initial
self-calibration.
Power-On Calibration
The ADC performs a self-calibration at start-up. An internal
power-on-reset (POR) circuit detects the supply voltage
ramps and initiates the calibration when the analog and
digital supply voltages are above a threshold. The following
conditions must be adhered to for the power-on calibration to
execute successfully:
A frequency-stable conversion clock must be applied to
the CLKP/CLKN pins
DNC pins (especially 3, 4 and 18) must not be pulled up or
down
SDO (pin 66) must be high
RESETN (pin 25) must begin low
SPI communications must not be attempted
A user-initiated reset can subsequently be invoked in the
event that the above conditions cannot be met at power-up.
The SDO pin requires an external 4.7k
Ω pull-up to OVDD. If
the SDO pin is pulled low externally during power-up,
calibration will not be executed properly.
After the power supply has stabilized the internal POR
releases RESETN and an internal pull-up pulls it high, which
starts the calibration sequence. If a subsequent
user-initiated reset is required, the RESETN pin should be
connected to an open-drain driver with a drive strength of
less than 0.5mA.
The calibration sequence is initiated on the rising edge of
RESETN, as shown in Figure 23. The over-range output
(OR) is set high once RESETN is pulled low, and remains in
that state until calibration is complete. The OR output returns
to normal operation at that time, so it is important that the
analog input be within the converter’s full-scale range to
observe the transition. If the input is in an over-range
condition the OR pin will stay high, and it will not be possible
to detect the end of the calibration cycle.
FIGURE 22. ADC CORE BLOCK DIAGRAM
DIGITAL
ERROR
CORRECTION
SHA
1.25V
INP
INN
CLOCK
GENERATION
2.5-BIT
FLASH
6-STAGE
1.5-BIT/STAGE
3-STAGE
1-BIT/STAGE
3-BIT
FLASH
LVDS/LVCMOS
OUTPUTS
+
–
KAD5610P
相關PDF資料 |
PDF描述 |
|---|---|
| KAD5612P-17Q72 | IC ADC 12BIT 170MSPS DUAL 72-QFN |
| LA72715NV-TLM-E | IC AUDIO DECODER JPN MTS 24SSOP |
| LICAL-DEC-LS001 | IC DECODER LOW SECURITY 8DIP |
| LICAL-DEC-MS001 | IC DECODER MS SERIES 20-SSOP |
| LICAL-ENC-MS001 | IC ENCODER MS SERIES 20-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KAD5612P | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P_09 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P_0909 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 12-Bit, 250/210/170/125MSPS A/D Converter |
| KAD5612P-12Q72 | 功能描述:IC ADC 12BIT 125MSPS DUAL 72-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:FemtoCharge™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| KAD5612P-17Q72 | 功能描述:IC ADC 12BIT 170MSPS DUAL 72-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:FemtoCharge™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。