- 您現在的位置：買賣IC網 > PDF目錄373177 > KS16114 (SAMSUNG SEMICONDUCTOR CO. LTD.) 9600/14400 bps FAX MODEM PDF資料下載
參數資料
| 型號： | KS16114 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 9600/14400 bps FAX MODEM |
| 中文描述： | 14400分之9600基點傳真調制解調器 |
| 文件頁數： | 30/69頁 |
| 文件大?。?/td> | 513K |
| 代理商： | KS16114 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
KS16112/4
9600/14400 bps FAX MODEM
-
30
-
In the high speed transmit mode ( all data configurations except FSK ), the modem sets P1S to indicate that
the P1 sequence is being transmitted. The P1 sequence is also referred to as the echo protector tone and
consists of 187.5 ms of unmodulated carrier followed by 20 ms of silence. In the receive mode the P1S bit
has no significance.
In the high speed transmit mode ( all data configurations except FSK ), the modem sets P2S to indicate that
the P2 sequence is being transmitted. In the receive mode, the modem sets P2S to indicate that the modem
has detected an incoming P2 sequence and is in the process of searching for the P2 to PN transition.
When the PDME control bit is set, the modem is configured for parallel data mode. During parallel data
mode transmission, the modem accepts transmit data from DBFR ( 10 : 0 - 7 ) rather than the TXDI serial
input. During the receive mode the modem simultaneously outputs the received data to DBFR ( 10 : 0 - 7 )
and the RXDO serial output. HDLC framing is performed only in parallel data mode. When PDME is reset,
the modem is in serial data mode and the modem accepts transmit data via the TXDI serial input and
issues received data via the RXDO serial output.
PDME
Parallel Data Mode Enable
07 : 5 ( 0 )
P2S
P2 Sequence
0C : 2 ( - )
P1S
P1 Sequence
0C : 1 ( - )
The ORUR function is disabled if the AHEOF control bit is set. The ORUR bit is valid only while the modem
is configured for HDLC mode ( HDLCE is set ).
When programmable interrupts are enabled ( PINTE is set ). PINTA is set by the modem when the interrupt
condition specified by INTMSK, INTADR, ITRIG, and INTML is true. The modem asserts IRQ if PIRQ has
been previously reset by the host. PINTA is automatically reset when the host resets PIRQ.
PINTE
Programmable Interrupt Enable
1F : 4 ( 0 )
PINTA
Programmable Interrupt Active
When PINTE is set and the interrupt condition as specified by INTMSK, INTADR, ITRIG, and INTML is
true, the modem asserts IRQ if control bit PIRQ has been previously reset by the host. Bits INTMSK,
INTADR, ITRIG, INTML, and PIRQ have no effect on IRQ and PINTA when programmable interrupts are
disabled ( PINTE is reset ).
1F : 7 ( - )
PIRQ
Programmable Interrupt Request
1F : 3 ( - )
When PINTE is set and the interrupt condition is true as specified by INTMSK, INTADR, ITRIG, and INTML,
the modem asserts IRQ if control bit PIRQ has been previously reset by the host, PIRQ is set by the
modem when the programmable interrupt condition is true. The host must reset PIRQ after servicing the
interrupt. The modem will not assert IRQ when an interrupt condition is met unless PIRQ is reset.
相關PDF資料 |
PDF描述 |
|---|---|
| KS16112 | CAP 33PF 50V 5% NPO(C0G) SMD-0603 TR-7-PA |
| KS16116-02 | 9600 bps FAX MODEM(9600bps傳真調制解調器) |
| KS16117-02 | 14400 bps FAX MODEM(14400bps傳真調制解調器) |
| KS16118 | 9600bps FAX super one-chip(9600bps傳真調制解調器) |
| KS16120B | DSP for Digital Answering Phone(用于數字應答電話的DSP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS16-14 | 制造商:MAJOR 功能描述: |
| KS-16287L1 | 制造商:WSTELC 功能描述: |
| KS-16287L2 | 制造商:WSTELC 功能描述: |
| KS16390 | 制造商: 功能描述: 制造商:Cornell Dubilier Electronics 功能描述: 制造商:undefined 功能描述: |
| KS16479 | 制造商:Olympic Controls Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。