參數資料
型號： KSZ8051MLL TR
廠商： Micrel Inc
文件頁數： 13/48頁
文件大小： 0K
描述： TXRX PHY 10/T100 3.3V MII 48LQFP
標準包裝： 1,000
類型： PHY 收發器
驅動器/接收器數： 1/1
規程： MII
電源電壓： 1.8V，2.5V，3.3V
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 帶卷 (TR)
配用： 576-3864-ND - BOARD EVALUATION FOR KSZ8051MLL
Micrel, Inc.
KSZ8051MLL
July 2010
20
M9999-071210-1.0
MII Management (MIIM) Interface
The KSZ8051MLL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state
of the KSZ8051MLL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows the external controller
to communicate with one or more PHY devices.
A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE
802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section
for details.
As the default, the KSZ8051MLL supports unique PHY addresses 1 to 7, and broadcast PHY address 0. The latter is
defined per the IEEE 802.3 Specification, and can be used to read/write to a single KSZ8051MLL device, or write to
multiple KSZ8051MLL devices simultaneously.
Optionally, PHY address 0 can be disabled as the broadcast address by either hardware pin strapping (B-CAST_OFF, pin
28) or software (register 16h, bit 9), and assigned as a unique PHY address.
The PHYAD[2:0] strapping pins are used to assign a unique PHY address between 0 and 7 to each KSZ8051MLL device.
Table 3 shows the MII Management frame format for the KSZ8051MLL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 3. MII Management Frame Format – for KSZ8051MLL
Interrupt (INTRP)
INTRP (pin 32) is an optional interrupt signal that is used to inform the external controller that there has been a status
update to the KSZ8051MLL PHY register. Register 1Bh, bits [15:8] are the interrupt control bits to enable and disable the
conditions for asserting the INTRP signal. Register 1Bh, bits [7:0] are the interrupt status bits to indicate which interrupt
conditions have occurred. The interrupt status bits are cleared after reading register 1Bh.
Register 1Fh, bit 9 sets the interrupt level to active high or active low. The default is active low.
The MII management bus option gives the MAC processor complete access to the KSZ8051MLL control and status
registers. Additionally, an interrupt pin eliminates the need for the processor to poll the PHY for status change.
相關PDF資料
PDF描述
KSZ8051MLLI TR TXRX PHY 10/T100 3.3V MII 48LQFP
KSZ8051MNLI TXRX PHY 10/T100 3.3V 32QFN
KSZ8051RNLI TR TXRX PHY 10/T100 3.3V RMII 32QFN
KSZ8692XPB IC ARM9 PHY 10/100MBPS 400-PBGA
KSZ8695P IC ARM9 W/MMU PHY 10/100 289PBGA
相關代理商/技術參數
參數描述
KSZ8051MNL 功能描述:TXRX PHY 10/T100 3.3V MII 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8051MNL TR 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8051MNL-EVAL 功能描述:以太網開發工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8051MNLI 功能描述:TXRX PHY 10/T100 3.3V 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8051MNLI TR 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (32-QFN, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*