- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8893FQL (Micrel Inc)IC SWITCH FAST ETH 3PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8893FQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 59/117頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH FAST ETH 3PORT 128PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII，RMII，SNI |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-1603-ND - EVAL KIT EXPERIMENTAL KSZ8893MQL |
| 其它名稱： | 576-1565 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Micrel, Inc.
KSZ8893FQL
October 2007
46
M9999-101607-1.3
QoS Priority Support
The KSZ8893FQL provides Quality of Service (QoS) for applications such as VoIP and video conferencing. Offering
four priority queues per port, the per-port transmit queue can be split into four priority queues: Queue 3 is the highest
priority queue and Queue 0 is the lowest priority queue. Bit [0] of registers 16, 32 and 48 is used to enable split transmit
queues for ports 1, 2 and 3, respectively. If a port's transmit queue is not split, high priority and low priority packets
have equal priority in the transmit queue.
There is an additional option to either always deliver high priority packets first or use weighted fair queuing for the four
priority queues. This global option is set and explained in bit [3] of register 5.
Port-Based Priority
With port-based priority, each ingress port is individually classified as a high priority receiving port. All packets received
at the high priority receiving port are marked as high priority and are sent to the high-priority transmit queue if the
corresponding transmit queue is split. Bits [4:3] of registers 16, 32 and 48 are used to enable port-based priority for
ports 1, 2 and 3, respectively.
802.1p-Based Priority
For 802.1p-based priority, the KSZ8893FQL examines the ingress (incoming) packets to determine whether they are
tagged. If tagged, the 3-bit priority field in the VLAN tag is retrieved and compared against the “priority mapping” value,
as specified by the registers 12 and 13. The “priority mapping” value is programmable.
The following figure illustrates how the 802.1p priority field is embedded in the 802.1Q VLAN tag.
Figure 9. 802.1p Priority Field Format
802.1p-based priority is enabled by bit [5] of registers 16, 32 and 48 for ports 1, 2 and 3, respectively.
The KSZ8893FQL provides the option to insert or remove the priority tagged frame's header at each individual egress
port. This header, consisting of the 2 bytes VLAN Protocol ID (VPID) and the 2-byte Tag Control Information field (TCI),
is also referred to as the IEEE 802.1Q VLAN tag.
Tag Insertion
is enabled by bit [2] of registers 16, 32 and 48 for ports 1, 2 and 3, respectively. At the egress port,
untagged packets are tagged with the ingress port’s default tag. The default tags are programmed in register sets
{19,20}, {35,36} and {51,52} for ports 1, 2 and 3, respectively. The KSZ8893FQL will not add tags to already tagged
packets.
Tag Removal
is enabled by bit [1] of registers 16, 32 and 48 for ports 1, 2 and 3, respectively. At the egress port,
tagged packets will have their 802.1Q VLAN Tags removed. The KSZ8893FQL will not modify untagged packets.
The CRC is recalculated for both tag insertion and tag removal.
802.1p Priority Field Re-mapping
is a QoS feature that allows the KSZ8893FQL to set the “User Priority Ceiling” at
any ingress port. If the ingress packet’s priority field has a higher priority value than the default tag’s priority field of the
ingress port, the packet’s priority field is replaced with the default tag’s priority field. The “User Priority Ceiling” is
enabled by bit [3] of registers 17, 33 and 49 for ports 1, 2 and 3, respectively.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8895MQI | IC ETHERNET SWITCH 5PORT 128PQFP |
| KSZ8895MQ | IC ETHERNET SW 5PORT 128-PQFP |
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8893FQL-EVAL | 功能描述:以太網開發工具 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8893FQL-FX | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893FQLI-FX | 功能描述:以太網 IC 3-Port Ethernet Switch w MII/RMII Interface + 100FX (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL TR | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 100-Ball LFBGA (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。