- 您現在的位置：買賣IC網 > PDF目錄19820 > LAMXO640C-3TN100E (Lattice Semiconductor Corporation)IC FPGA AUTO 640LUTS 100TQFP PDF資料下載
參數資料
| 型號： | LAMXO640C-3TN100E |
| 廠商： | Lattice Semiconductor Corporation |
| 文件頁數： | 11/77頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA AUTO 640LUTS 100TQFP |
| 標準包裝： | 90 |
| 系列： | LA-MachXO |
| 可編程類型： | 系統內可編程 |
| 最大延遲時間 tpd(1)： | 4.9ns |
| 電壓電源 - 內部： | 1.71 V ~ 3.465 V |
| 宏單元數： | 320 |
| 輸入/輸出數： | 74 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 包裝： | 托盤 |
| 其它名稱： | 220-1639 LAMXO640C-3TN100E-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
2-16
Architecture
Lattice Semiconductor
LA-MachXO Automotive Family Data Sheet
of the devices also support differential input buffers. PCI clamps are available on the top Bank I/O buffers. The
PCI clamp is enabled after VCC, VCCAUX, and VCCIO are at valid operating levels and the device has been con-
gured.
The two pads in the pair are described as “true” and “comp”, where the true pad is associated with the positive
side of the differential input buffer and the comp (complementary) pad is associated with the negative side of
the differential input buffer.
2.
Left and Right sysIO Buffer Pairs
The sysIO buffer pairs in the left and right Banks of the device consist of two single-ended output drivers and
two sets of single-ended input buffers (supporting ratioed and absolute input levels). The devices also have a
differential driver per output pair. The referenced input buffer can also be congured as a differential input
buffer. In these Banks the two pads in the pair are described as “true” and “comp”, where the true pad is asso-
ciated with the positive side of the differential I/O, and the comp (complementary) pad is associated with the
negative side of the differential I/O.
Typical I/O Behavior During Power-up
The internal power-on-reset (POR) signal is deactivated when VCC and VCCAUX have reached satisfactory levels.
After the POR signal is deactivated, the FPGA core logic becomes active. It is the user’s responsibility to ensure
that all VCCIO Banks are active with valid input logic levels to properly control the output logic states of all the I/O
Banks that are critical to the application. The default conguration of the I/O pins in a blank device is tri-state with a
weak pull-up to VCCIO. The I/O pins will maintain the blank conguration until VCC, VCCAUX and VCCIO have
reached satisfactory levels at which time the I/Os will take on the user-congured settings.
The VCC and VCCAUX supply the power to the FPGA core fabric, whereas the VCCIO supplies power to the I/O buff-
ers. In order to simplify system design while providing consistent and predictable I/O behavior, the I/O buffers
should be powered up along with the FPGA core fabric. Therefore, VCCIO supplies should be powered up before or
together with the VCC and VCCAUX supplies
Supported Standards
The LA-MachXO sysIO buffer supports both single-ended and differential standards. Single-ended standards can
be further subdivided into LVCMOS and LVTTL. The buffer supports the LVTTL, LVCMOS 1.2, 1.5, 1.8, 2.5, and
3.3V standards. In the LVCMOS and LVTTL modes, the buffer has individually congurable options for drive
strength, bus maintenance (weak pull-up, weak pull-down, bus-keeper latch or none) and open drain. BLVDS and
LVPECL output emulation is supported on all devices. The LA-MachXO1200 and LA-MachXO2280 support on-chip
LVDS output buffers on approximately 50% of the I/Os on the left and right Banks. Differential receivers for LVDS,
BLVDS and LVPECL are supported on all Banks of LA-MachXO1200 and LA-MachXO2280 devices. PCI support is
provided in the top Banks of the LA-MachXO1200 and LA-MachXO2280 devices. Table 2-8 summarizes the I/O
characteristics of the devices in the LA-MachXO family.
Tables 2-9 and 2-10 show the I/O standards (together with their supply and reference voltages) supported by the
LA-MachXO devices. For further information on utilizing the sysIO buffer to support a variety of standards please
see the details of additional technical documentation at the end of this data sheet.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8518EUB+T | IC REG LDO ADJ 1A 10-UMAX |
| RCM12DRUS | CONN EDGECARD 24POS DIP .156 SLD |
| GRM31CR60J226KE19L | CAP CER 22UF 6.3V 10% X5R 1206 |
| M4A5-64/32-7VI | IC CPLD ISP 4A 64MC 44TQFP |
| MAX6469TA15BD3+T | IC REG LDO 1.5V/ADJ .3A 8-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAMXO640C-3TN144E | 功能描述:CPLD - 復雜可編程邏輯器件 Auto Grade (AEC-Q100 ) MachXO640C RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| LAMXO640E | 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LA-MachXO Automotive Family Data Sheet |
| LAMXO640E-3FTN256E | 功能描述:CPLD - 復雜可編程邏輯器件 Auto Grade (AEC-Q100 ) MachXO640E RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| LAMXO640E-3TN100E | 功能描述:CPLD - 復雜可編程邏輯器件 Auto Grade (AEC-Q100 ) MachXO640E RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| LAMXO640E-3TN144E | 功能描述:CPLD - 復雜可編程邏輯器件 Auto Grade (AEC-Q100 ) MachXO640E RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
發布緊急采購，3分鐘左右您將得到回復。