參數資料
型號： M25PE16-VMP6TP
廠商： 意法半導體
元件分類： DRAM
英文描述： 4 Mbit Uniform Sector, Serial Flash Memory
中文描述： 4兆位統一部門，串行閃存
文件頁數： 40/56頁
文件大小： 334K
代理商： M25PE16-VMP6TP
Instructions
M25PE16
40/56
6.15
Bulk Erase (BE)
The Bulk Erase (BE) instruction sets all bits to 1 (FFh). Before it can be accepted, a Write
Enable (WREN) instruction must previously have been executed. After the Write Enable
(WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL).
The Bulk Erase (BE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code on Serial Data Input (D). Chip Select (S) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in
Figure 20
.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Bulk Erase instruction is not executed. As soon as Chip Select (S)
is driven High, the self-timed Bulk Erase cycle (whose duration is t
BE
) is initiated. While the
Bulk Erase cycle is in progress, the Status Register may be read to check the value of the
Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Bulk
Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is
completed, the Write Enable Latch (WEL) bit is reset.
Any Bulk Erase (BE) instruction, while an Erase, Program or Write cycle is in progress, is
rejected without having any effects on the cycle that is in progress. A Bulk Erase (BE)
instruction is ignored if at least one sector or subsector is write-protected (Hardware or
Software protection).
If Reset (RESET) is driven Low while a Bulk Erase (BE) cycle is in progress, the Bulk Erase
cycle is interrupted and data may not be erased correctly (see
Table 12: Device status after
a RESET Low pulse
). On RESET going Low, the device enters the Reset mode and a time
of t
RHSL
is then required before the device can be re-selected by driving Chip Select (S)
Low. For the value of t
RHSL
see
Table 20: Timings after a RESET Low pulse
in
Section 11:
DC and AC parameters
.
Figure 20.
Bulk Erase (BE) instruction sequence
C
D
AI03752D
S
2
1
3
4
5
6
7
0
Instruction
相關PDF資料
PDF描述
M25PE16-VMW6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE16-VMW6G 功能描述:閃存 16 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE16-VMW6P 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
M25PE16-VMW6TG 功能描述:閃存 16 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE16-VMW6TP 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
M25PE20 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*