參數資料
型號: M25PE16-VMP6TP
廠商: 意法半導體
元件分類: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 43/56頁
文件大?。?/td> 334K
代理商: M25PE16-VMP6TP
M25PE16
Power-up and Power-down
43/56
7
Power-up and Power-down
At Power-up and Power-down, the device must not be selected (that is Chip Select (S) must
follow the voltage applied on V
CC
) until V
CC
reaches the correct value:
V
CC
(min) at Power-up, and then for a further delay of t
VSL
V
SS
at Power-down
A safe configuration is provided in
Section 3: SPI modes
.
To avoid data corruption and inadvertent write operations during power-up, a Power On
Reset (POR) circuit is included. The logic inside the device is held reset while V
CC
is less
than the Power On Reset (POR) threshold voltage, V
WI
– all operations are disabled, and
the device does not respond to any instruction.
Moreover, the device ignores all Write Enable (WREN), Page Write (PW), Page Program
(PP), Page Erase (PE), Sector Erase (SE), SubSector Erase (SSE), Bulk Erase (BE), Write
Status Register (WRSR) and Write to Lock Register (WRLR) instructions until a time delay
of t
PUW
has elapsed after the moment that V
CC
rises above the V
WI
threshold. However, the
correct operation of the device is not guaranteed if, by this time, V
CC
is still below V
CC
(min).
No Write, Program or Erase instructions should be sent until the later of:
t
PUW
after V
CC
passed the V
WI
threshold
t
VSL
after V
CC
passed the V
CC
(min) level
These values are specified in
Table 11
.
If the delay, t
VSL
, has elapsed, after V
CC
has risen above V
CC
(min), the device can be
selected for READ instructions even if the t
PUW
delay is not yet fully elapsed.
As an extra protection, the Reset (RESET) signal could be driven Low for the whole duration
of the Power-up and Power-down phases.
At Power-up, the device is in the following state:
The device is in the Standby mode (not the Deep Power-down mode).
The Write Enable Latch (WEL) bit is reset.
The Write In Progress (WIP) bit is reset
The Lock Registers are reset (Write Lock bit, Lock Down bit) = (0, 0)
Normal precautions must be taken for supply rail decoupling, to stabilize the V
CC
supply.
Each device in a system should have the V
CC
line decoupled by a suitable capacitor close to
the package pins. (Generally, this capacitor is of the order of 100 nF).
At Power-down, when V
CC
drops from the operating voltage, to below the Power On Reset
(POR) threshold voltage, V
WI
, all operations are disabled and the device does not respond
to any instruction. (The designer needs to be aware that if a Power-down occurs while a
Write, Program or Erase cycle is in progress, some data corruption can result.)
相關PDF資料
PDF描述
M25PE16-VMW6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMW6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE16-VMW6G 功能描述:閃存 16 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE16-VMW6P 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
M25PE16-VMW6TG 功能描述:閃存 16 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE16-VMW6TP 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
M25PE20 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout