- 您現在的位置：買賣IC網 > PDF目錄370837 > M32000D3FP (Mitsubishi Electric Corporation) SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M32000D3FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片32位CMOS微機 |
| 文件頁數： | 19/45頁 |
| 文件大小： | 565K |
| 代理商： | M32000D3FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
M32000D3FP
19
Bus interface unit (BIU)
The M32000D3FP has the following signals related to the external
bus.
Address (A8 to A30)
The M32000D3FP has a 24-bit address bus (A8 to A31) correspond-
ing to a 16 MB address space. Of these, A31 (the LSB) is not output
externally. In write cycles, the validity of the two bytes output on the
16-bit data bus is indicated by BCH and/or BCL. In read cycles, the
16-bit data bus is always read, however, only data in the valid byte
position in the M32000D3FP is transferred. The address pins are
bidirectional. If the M32000D3FP is in the hold state and the internal
DRAM is accessed from an external bus master, the address signal
is input from the system bus side.
Space identifier (SID)
The space identifier is used to specify user space and I/O space.
user space: SID = "L"
I/O space: SID = "H"
If the M32000D3FP is in the hold state and the internal DRAM is
accessed from an external bus master, the "L" level should be input
to SID from the system bus side.
Byte control (BCH, BCL)
Byte control signals indicate the byte position of valid data trans-
ferred of the external bus cycle. BCH corresponds to the MSB side
(D0 to D7), and BCL corresponds to the LSB side (D8 to D15). Dur-
ing the bus read cycle, both BCH and BCL are an "L" level. During
the bus write cycle, BCH and/or BCL go to an "L" level depending on
the bytes to be written. If the M32000D3FP is in the hold state and
the internal DRAM is accessed from an external bus master, the byte
control signal is input from the system bus side.
Data bus (D0 to D15)
The M32000D3FP has a 16-bit data bus to access external devices.
If the M32000D3FP is in the hold state and the internal DRAM is
accessed from an external bus master, the data bus is used as a
data I/O bus from the system bus side.
Bus start (BS)
When the M32000D3FP drives the bus cycle to the system bus, an
"L" level is output to BS at the start of the bus cycle. Also, for a burst
transfer, the BS signal is output for each transfer cycle. The BS sig-
nal is not output when accessing internal resources such as the in-
ternal DRAM or internal I/O registers.
Bus status (ST)
The ST signal identifies whether the bus cycle the M32000D3FP is
driving is an instruction fetch cycle or an operand access cycle.
instruction fetch access: ST = "L"
operand access: ST = "H"
hold: ST = high-impedance
idle: ST = undefined
Read/write (R/W)
The M32000D3FP outputs a R/W signal to identify whether the ex-
ternal bus cycle is a read or write operation. When accessing the
internal DRAM from an external bus master, a R/W signal is input
from the system bus side.
read bus cycle: R/W = "H"
Burst (BURST)
The M32000D3FP drives two consecutive bus cycles to access 32-
bit data located on the 32-bit boundary. In instruction fetching, it drives
a maximum of 8 (fixed to 8 cycles in instruction cache mode) con-
secutive read cycles to access data located on the 128-bit boundary.
While driving these consecutive bus cycles, the M32000D3FP out-
puts "L" level to BURST. When accessing 32-bit data, the address of
the MSB-side 16 bits are output before the address of the LSB side
16 bits. When accessing 128-bit data, the addresses are output for
every access cycle from the arbitrary 16-bit aligned addresses to
wraparound within the 128-bit boundary.
Data complete (DC)
When starting an external bus cycle, the M32000D3FP automati-
cally inserts wait cycles until the DC signal is input from external.
Wait control using the DC signal is effective also for bus cycles dur-
ing burst transfer. When the M32000D3FP is in the hold state and if
the CS signal is input, the M32000D3FP outputs the DC signal to
notify the external bus master that internal DRAM access is com-
plete.
_____ _____
Hold control (HREQ, HACK)
The hold state is the state when the external bus access stops and
all pins go to a high-impedance state. However, the internal DRAM
can be accessed while the external bus is in the hold state. To put
the M32000D3FP into the hold state, input an "L" level to HREQ.
When the hold request is accepted and the M32000D3FP enters the
hold state, an "L" level is output from HACK.
相關PDF資料 |
PDF描述 |
|---|---|
| M32000D4 | SINGLE CHIP 32 BIT CMOS MICROCOMPUTER |
| M32000D4AFP | SINGLE CHIP 32 BIT CMOS MICROCOMPUTER |
| M32170F3VFP | SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER |
| M32174F3VFP | SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER |
| M32170F3VFG | 32-BIT RISC SINGLE-CHIP MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M32000D4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 32 BIT CMOS MICROCOMPUTER |
| M32000D4AFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 32 BIT CMOS MICROCOMPUTER |
| M32000D4BFP-80 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER |
| M32002AGLJ | 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:9x14 mm, 3.3/2.5/1.8 Volt, PECL/LVDS/CML, VCXO |
| M32002AGMJ | 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:9x14 mm, 3.3/2.5/1.8 Volt, PECL/LVDS/CML, VCXO |
發布緊急采購，3分鐘左右您將得到回復。