參數資料
型號： M37754S4CHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100
封裝： 0.50 MM PITCH, PLASTIC, QFP-100
文件頁數： 73/115頁
文件大小： 1571K
代理商： M37754S4CHP
59
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(2) Repeat mode
Repeat mode is selected when bit 3 of A-D control register 0 is “1”,
bit 4 is “0” and bit 2 of A-D control register 1 is “0”.
The operation of this mode is the same as the operation of one-shot
mode except that when A-D conversion of the selected pin is com-
plete and the result is stored in the A-D register, conversion does not
stop, but is repeated.
No interrupt request is generated in this mode. Furthermore, if soft-
ware trigger is selected, the A-D conversion start bit is not cleared.
The contents of the A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
(3) Single sweep mode
Single sweep mode is selected when bit 3 of A-D control register 0
is “0”, bit 4 is “1” and bit 2 of A-D control register 1 is “0”.
In the single sweep mode, the number of analog input pins to be
swept can be selected. Analog input pins are selected by bits 1 and
0 of the A-D control register 1 (address 1F16). Two pins, four pins,
six pins, or eight pins can be selected as analog input pins, depend-
ing on the contents of these bits.
A-D conversion is performed only for selected input pins. After A-D
conversion is performed for input of AN0 pin, the conversion result
is stored in A-D register 0, and in the same way, A-D conversion is
performed for selected pins one after another. After A-D conversion
is performed for all selected pins, the sweep is stopped.
A-D conversion can be started with a software trigger or with an ex-
ternal trigger input. A software trigger is selected when bit 5 is “0”
and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started when
A-D control register 0 bit 6 (A-D conversion start bit) is set to “1.”
When A-D conversion of all selected pins end, the interrupt request
bit of the A-D conversion interrupt control register is set to “1.” At the
same time, A-D conversion start bit is cleared to “0” and A-D conver-
sion stops.
When an external trigger is selected, A-D conversion starts when
_____
the A-D conversion start bit is “1” and the ADTRG input changes from
“H” to “L”. In this case, the A-D conversion result which is stored in
_____
the A-D register 7 becomes invalid because the ADTRG pin is multi-
plexed with AN7 pin.
The operation by external trigger is the same as that by software
trigger except that the A-D conversion start bit is not cleared to “0”
after A-D conversion and a retrigger can be available during A-D
conversion.
(4) Repeat sweep mode 0
Repeat sweep mode 0 is selected when bit 3 of A-D control register
0 is “1”, bit 4 is “1” and bit 2 of A-D control register 1 is “0”.
The difference from the single sweep mode is that A-D conversion
does not stop after conversion for all selected pins, but repeats
again from the AN0 pin. The repeat is performed among the selected
pins. Also, no interrupt request is generated. Furthermore, if soft-
ware trigger is selected, the A-D convension start bit is not cleared.
The A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
(5) Repeat sweep mode 1
Repeat sweep mode 1 is selected when bit 3 of A-D control register
0 is “1”, bit 4 is “1” and bit 2 of A-D control register 1 is “1”.
The difference from the repeat sweep mode 0 is that A-D conversion
for one unselected pin is performed each time when A-D conversion
for selected pins is completed and A-D conversion is repeated once
again from AN0 pin. The number of analog input pins to be swept is
also different.
The analog input pins for repeatedly sweep are selected with bits 1
and 0 of A-D control register 1. The contents of these pins are used
to select one pin, two pins, three pins, or four pins.
The unselected pins are converted from the pin next to the pins se-
lected as repeat sweep pins. No interrupt request is generated. Fur-
thermore, if software trigger is selected, the A-D conversion start bit
is not cleared.
The A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
Note: Clear the interrupt request bit of the A-D interrupt control reg-
ister (bit 3 at address 7016) before using the A-D interrupt. It is
because the interrupt request bit is undefined just after reset.
相關PDF資料
PDF描述
M37754M8C-XXXGP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100
M37777E9AGS 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC100
M34550M6A-XXXFP 4-BIT, MROM, 1.6 MHz, MICROCONTROLLER, PQFP80
M37776M5AXXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M37775E9AGS 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC100
相關代理商/技術參數
參數描述
M3775PR-H400CL 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR
M3775RK-0.75A 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR
M3775RK-C0.50A 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR
M3775RK-C0.50B 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR
M3775RK-C0.50C 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*