參數資料
型號： M50FW002K
廠商： 意法半導體
英文描述： 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory
中文描述： 2兆位的256Kb × 8，啟動塊3V電源閃存固件集線器
文件頁數： 12/39頁
文件大?。?/td> 254K
代理商： M50FW002K
M50FW002
12/39
Table 8. Commands
Note:
X Don’t Care, PA Program Address, PD Program Data, A
1,2,3,4
Consecutive Addresses, BA Any address in the Block.
Read Memory Array
: After a Read Memory Array command, read the memory as normal until another command is issued.
Read Status Register
: After a Read Status Register command, read the Status Register as normal until another command is issued.
Read Electronic Signature
: After a Read Electronic Signature command, read Manufacturer Code, Device Code until another com-
mand is issued.
Block Erase, Byte Program
: After these commands, read the Status Register until the command completes and another command
is issued.
Quadruple Byte Program
: This command is only valid in A/A Mux mode. Addresses A
1
, A
2
, A
3
and A
4
must be consecutive addresses
differing only for address bit A0 and A1. After this command read the Status Register until the command completes and another com-
mand is issued.
Chip Erase
: This command is only valid in A/A Mux mode. After this command, read the Status Register until the command completes
and another command is issued.
Clear Status Register
: After the Clear Status Register command bits 1, 3, 4 and 5 in the Status Register are reset to ‘0’.
Program/Erase Suspend
: After the Program/Erase Suspend command has been accepted, issue Read Memory Array, Read Status
Register, Program (during Erase suspend) and Program/Erase resume commands.
Program/Erase Resume
: After the Program/Erase Resume command the suspended Program/Erase operation resumes, read the
Status Register until the Program/Erase Controller completes and the memory returns to Read Mode.
Invalid/Reserved
: Do not use Invalid or Reserved commands.
Command
C
Bus Write Operations
1st
2nd
3rd
4th
5th
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Read Memory Array
1
X
FFh
Read Status Register
1
X
70h
Read Electronic Signature
1
X
90h
1
X
98h
Program
2
X
40h
PA
PD
2
X
10h
PA
PD
Quadruple Byte Program
5
X
30h
A
1
PD
A
2
PD
A
3
PD
A
4
PD
Chip Erase
2
X
80h
X
10h
Block Erase
2
X
20h
BA
D0h
Clear Status Register
1
X
50h
Program/Erase Suspend
1
X
B0h
Program/Erase Resume
1
X
D0h
Invalid/Reserved
1
X
00h
1
X
01h
1
X
60h
1
X
2Fh
1
X
C0h
相關PDF資料
PDF描述
M50FW002 2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory
M50LPW041K1T 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW041N1T 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW041N 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW041K 4 Mbit 512Kb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50FW002K1 功能描述:閃存 3.6V 2M (256Kx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FW002K1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory
M50FW002K5T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Mbit 256Kb x8, Boot Block 3V Supply Firmware Hub Flash Memory
M50FW016 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW016N 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*