- 您現在的位置：買賣IC網 > PDF目錄180232 > M58LW128A150N1 (STMICROELECTRONICS) 8M X 16 FLASH 3V PROM, 150 ns, PDSO56 PDF資料下載
參數資料
| 型號： | M58LW128A150N1 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 150 ns, PDSO56 |
| 封裝： | 14 X 20 MM, PLASTIC, TSOP-56 |
| 文件頁數： | 5/65頁 |
| 文件大?。?/td> | 378K |
| 代理商： | M58LW128A150N1 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
13/65
M58LW128A, M58LW128B
is the LSB of the address bus. When WORD is
High, VIH, the Double-Word wide x32 Bus Width is
selected and the data is read and written to on
DQ0-DQ31; A2 is the LSB of the address bus and
A1 is don’t care.
Ready/Busy (RB). The Ready/Busy output, RB,
is an open-drain output that can be used to identify
if the Program/Erase Controller is currently active.
When Ready/Busy is high impedance, the memo-
ry is ready for any read, program or erase opera-
tion. Ready/Busy is Low, VOL, during program and
erase operations. When the device is busy it will
not accept any additional Program or Erase com-
mands except Program/Erase Suspend. When the
Program/Erase Controller is idle, or suspended,
Ready Busy can float High through a pull-up resis-
tor.
The use of an open-drain output allows the Ready/
Busy pins from several memories to be connected
to a single pull-up resistor. A Low will then indicate
that one, or more, of the memories is busy.
Ready/Busy is not Low during a reset unless the
reset was applied when the Program/Erase Con-
troller was active; Ready/Busy can rise before Re-
set/Power-Down rises.
Program/Erase Enable (VPP). The
Program/
Erase Enable input, VPP, is used to protect all
blocks, preventing Program and Erase operations
from affecting their data.
When Program/Erase Enable is Low, VIL, any pro-
gram or erase operation sent to the Command In-
terface will cause the VPP Status bit (bit3) in the
Status Register to be set. When Program/Erase
Enable is High, VIH, program and erase operations
can be performed on unprotected blocks. Pro-
gram/Erase Enable must be kept High during all
Program, Erase, Block Protect and Block Unpro-
tect operations, otherwise the operation is not
guaranteed to succeed and data may become cor-
rupt.
VDD Supply Voltage. The Supply Voltage, VDD,
is the core power supply. All internal circuits draw
their current from the VDD pin, including the Pro-
gram/Erase Controller.
A 0.1 F capacitor should be connected between
the Supply Voltage, VDD, and the Ground, VSS,to
decouple the current surges from the power sup-
ply. The PCB track widths must be sufficient to
carry the currents required during all operations of
the parts, see Table 16, DC Characteristics, for
maximum current supply requirements.
Input/Output Supply Voltage (VDDQ). The
In-
put/Output Supply Voltage, VDDQ, is the input/out-
put buffer power supply. All input and output pins
and voltage references are powered and mea-
sured relative to the Input/Output Supply Voltage
pin, VDDQ.
The Input/Output Supply Voltage, VDDQ, must al-
ways be equal or less than the VDD Supply Volt-
age, including during Power-Up.
A 0.1 F capacitor should be connected between
the Input/Output Supply Voltage, VDDQ, and the
Ground, VSSQ, to decouple the current surges
from the power supply. If VDDQ and VDD are con-
nected together then only one decoupling capaci-
tor is required.
Ground (VSS). Ground, VSS, is the reference for
all core power supply voltages.
Ground (VSSQ). Ground, VSSQ, is the reference
for input/output voltage measurements. It is es-
sential to connect VSS and VSSQ to the same
ground.
相關PDF資料 |
PDF描述 |
|---|---|
| M58WR064HU70ZB6U | 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 |
| M59DR032F100N1T | 2M X 16 FLASH 1.8V PROM, 100 ns, PDSO48 |
| M5F7924 | 24 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7920 | 20 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7918 | 18 V FIXED NEGATIVE REGULATOR, PSFM3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58LW128A150N1E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x16 or 4Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LW128A150N1F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x16 or 4Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LW128A150N1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x16 or 4Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LW128A150N6E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x16 or 4Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
| M58LW128A150N6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x16 or 4Mb x32, Uniform Block, Burst 3V Supply Flash Memories |
發布緊急采購，3分鐘左右您將得到回復。