- 您現在的位置：買賣IC網 > PDF目錄377930 > MB90F897SPMT (FUJITSU LTD) 10-Bit Buffers/Drivers With 3-State Outputs 24-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F897SPMT |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 10-Bit Buffers/Drivers With 3-State Outputs 24-CDIP -55 to 125 |
| 中文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 58/78頁 |
| 文件大小： | 746K |
| 代理商： | MB90F897SPMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
MB90895 Series
58
(Continued)
*6 :
Applicable to pins: P10 to P17, P20 to P27, P30 to P33, P35, P36, P37, P40 to P44, P50 to P57
Note: P35 and P36 are MB90F897S only.
Use within recommended operating conditions.
Use at DC voltage (current) .
The
+
B signal should always be applied a limiting resistance placed between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current to the
microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input potential
may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect other
devices.
Note that if a
+
B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power supply is
provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input
pins, etc.) cannot accept
+
B signal input.
Sample recommended circuits:
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
V
CC
R
Input/Output Equivalent circuits
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90M405 | Octal Edge-Triggered D-type Flip-Flops With Clear 20-CFP -55 to 125 |
| MB90M407 | Octal Edge-Triggered D-type Flip-Flops With Clear 20-LCCC -55 to 125 |
| MB90M408 | Octal Edge-Triggered D-type Flip-Flops With Clear 20-CDIP -55 to 125 |
| MB90MV405 | F2MC-16LX FAMILY 16-BIT MICROCONTROLLERS HARDWARE MANUAL ABSTRACTS |
| MB90M407APF | 16-Bit Original Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F947APFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
| MB90F962SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
發布緊急采購，3分鐘左右您將得到回復。