參數資料
型號： MBM29F080-12
廠商： Fujitsu Limited
英文描述： 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器)
中文描述： 8米（1米× 8）位快閃記憶體（1米× 8位5V的電源電壓閃速存儲器）
文件頁數： 16/50頁
文件大?。?/td> 667K
代理商： MBM29F080-12
16
MBM29F080
-90/-12
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of 15
μ
s to suspend the erase operation. When the device has entered the erase-suspended mode, the RY/BY
output pin and the DQ
7
bit will be at logic “1”, and DQ
6
will stop toggling. The user must use the address of the
erasing sector for reading DQ
6
and DQ
7
to determine if the erase operation has been suspended. Further writes
of the Erase Suspend command are ignored.
When the erase operation has been suspended, the device defaults to the erase-suspend-read mode. Reading
data in this mode is the same as reading from the standard read mode except that the data must be read from
sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the
device is in the erase-suspend-read mode will cause DQ
2
to toggle. (See the section on DQ
2
).
After entering the erase-suspend-read mode, the user can program the device by writing the appropriate com-
mand sequence for Byte Program. This program mode is known as the erase-suspend-program mode. Again,
programming in this mode is the same as programming in the regular Byte Program mode except that the data
must be programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended
sector while the device is in the erase-suspend-program mode will cause DQ
2
to toggle. The end of the erase-
suspended program operation is detected by the RY/BY output pin, Data polling of DQ
7
, or by the Toggle Bit I
(DQ
6
) which is the same as the regular Byte Program operation. Note that DQ
7
must be read from the byte
program address while DQ
6
can be read from any address.
To resume the operation of Sector Erase, the Resume command (30H) should be written. Any further writes of
the Resume command at this point will be ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
Write Operation Status
Notes: 1.Performing successive read operations from any address will cause DQ
6
to toggle.
2.Reading the byte address being programmed while in the erase-suspend program mode will indicate logic
“1” at the DQ
2
bit. However, successive reads from the erase-suspended sector will cause DQ
2
to toggle.
Table 7 Hardware Sequence Flags
Status
DQ
7
DQ
6
DQ
5
DQ
3
DQ
2
In progress
Embedded Program Algorithm
DQ
7
Toggle
0
0
1
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
Erase
Suspended
Mode
Erase Suspend Read
(Erase Suspended Sector)
1
1
0
0
Toggle
Erase Suspend Read
(Non-Erase Suspended Sector)
Data
Data
Data
Data
Data
Erase Suspend Program
(Non-Erase Suspended Sector)
DQ
7
Toggle
(Note 1)
0
0
1
(Note 2)
Exceeded
Time Limits
Embedded Program Algorithm
DQ
7
Toggle
1
0
1
Program/Erase in Embedded Erase Algorithm
0
Toggle
1
1
N/A
Erase
Suspended
Mode
Erase Suspend Program
(Non-Erase Suspended Sector)
DQ
7
Toggle
1
0
N/A
相關PDF資料
PDF描述
MBM29F080-90 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器)
MBM29F080A-55 8M (1M X 8) BIT
MBM29F080A Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
MBM29F080AC-90PF 8M (1M X 8) BIT
MBM29F080AC-90PFTN Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
相關代理商/技術參數
參數描述
MBM29F080-90PFTN 制造商:FUJITSU 功能描述:
MBM29F080A 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT
MBM29F080A-55 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F080A-55PF 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT
MBM29F080A-55PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*