- 您現在的位置：買賣IC網 > PDF目錄11546 > MC33989DW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33989DW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 15/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 26 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
| 配用： | KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33989
FUNCTIONAL DEVICE OPERATION
RESET AND WATCHDOG PINS, SOFTWARE WATCHDOG OPERATIONS
APPLICATION WAKE-UP FROM MCU SIDE
When application is in Stop mode, the wake-up event may come from the MCU side. In this case the MCU signals to the SBC
by a low to high transition on the CS pin. Then the SBC goes into Normal Request mode and generates an interrupt pulse at the
INT pin.
STOP MODE CURRENT MONITOR
If the VDD1 output current exceed an internal threshold (IDD1SWU), the SBC goes automatically into Normal Request mode and
generates an interrupt at the INT pin. The interrupt is not maskable and the interrupt register will has no flag set.
INTERRUPT GENERATION WHEN WAKE-UP FROM STOP MODE
When the SBC wakes up from Stop mode, it first enters the Normal Request mode before generating a pulse (10 s typical)
on the INT pin. These interrupts are not maskable, and the wake-up event can be read through the SPI registers (CANWU bit in
Reset Control Register (RCR) and LCTRx bit in Wake-up Register (WUR). In case of wake-up from Stop mode over current or
from forced wake-up, no bit is set. After the INT pulse the SBC accept SPI command after a time delay (tS1STSPI parameter).
SOFTWARE WATCHDOG IN STOP MODE
If Watchdog is enabled, the MCU has to wake-up independently of the SBC before the end of the SBC watchdog time. In order
to do this, the MCU must signal the wake-up to the SBC through the SPI wake-up (CS activation). The SBC then wakes up and
jumps into the Normal Request mode. MCU has to configured the SBC to go to either Normal or Standby mode. The MCU can
then decide to go back again to Stop mode.
When there is no MCU wake-up occurring within the watchdog timing, the SBC activates the Reset pin, jumping into the
Normal Request mode. The MCU can then be initialized.
STOP MODE ENTER COMMAND
Stop mode is entered at the end of the SPI message, and at the rising edge of the CS. Please refer to the t CSSTOP data in the
Once Stop mode is entered the SBC could wake-up from the V1 regulator overcurrent detection. In order to allow time for the
MCU to complete the last CPU instruction, allowing the MCU to enter its low power mode, a deglitcher time of typical 40 s is
implemented.
Figure 9 indicates the operation to enter Stop mode.
Figure 9. Operation Entering Stop Mode
RESET AND WATCHDOG PINS, SOFTWARE WATCHDOG OPERATIONS
SOFTWARE WATCHDOG (SELECTABLE WINDOW OR TIMEOUT WATCHDOG)
Software watchdog uses in the SBC Normal and Standby modes is to monitor MCU. The Watchdog can be either window or
timeout. This is selectable by SPI (register TIM1, bit WDW). Default is window watchdog. The period for the watchdog is
selectable from the SPI from 10 ms to 350 ms (register TIM1, bits WDT0 and WDT1). When the window watchdog is selected,
the closed window is the first part of the selected period, and the open window is the second part of the period. Refer to the SPI
SPI CS
SPI Stop/ Sleep Command
SBC in Normal or Stand-by mode
SBC in Stop mode
IDD1DGLT
tCSSTOP
with IDD1over I wake-up
no IDD1 over I wake-up
相關PDF資料 |
PDF描述 |
|---|---|
| MC33889DW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33389CDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33989DWR2 | 功能描述:CAN 接口集成電路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEG | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。