參數資料
型號: MC56F8323MFB60
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 數字信號處理
英文描述: 0-BIT, 120 MHz, OTHER DSP, PQFP64
封裝: PLASTIC, LQFP-64
文件頁數: 55/140頁
文件大?。?/td> 741K
代理商: MC56F8323MFB60
Signal Pins
56F8323 Technical Data, Rev. 17
Freescale Semiconductor
21
Preliminary
TMS
54
Schmitt
Input
Input,
pulled high
internally
Test Mode Select Input — This input pin is used to sequence the
JTAG TAP controller’s state machine. It is sampled on the rising
edge of TCK and has an on-chip pull-up resistor.
Note:
Always tie the TMS pin to VDD through a 2.2K resistor.
TDI
55
Schmitt
Input
Input,
pulled high
internally
Test Data Input — This input pin provides a serial input data stream
to the JTAG/EOnCE port. It is sampled on the rising edge of TCK and
has an on-chip pull-up resistor.
TDO
56
Output
In reset,
output is
disabled,
pull-up is
enabled
Test Data Output — This tri-stateable output pin provides a serial
output data stream from the JTAG/EOnCE port. It is driven in the
shift-IR and shift-DR controller states, and changes on the falling
edge of TCK.
TRST
58
Schmitt
Input
Input,
pulled high
internally
Test Reset — As an input, a low signal on this pin provides a reset
signal to the JTAG TAP controller. To ensure complete hardware
reset, TRST should be asserted whenever RESET is asserted. The
only exception occurs in a debugging environment when a hardware
device reset is required and the EOnCE/JTAG module must not be
reset. In this case, assert RESET, but do not assert TRST.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Note:
For normal operation, connect TRST directly to VSS. If the design
is to be used in a debugging environment, TRST may be tied to VSS through
a 1K resistor.
PHASEA0
(TA0)
(GPIOB7)
(oscillator_
clock)
52
Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Phase A — Quadrature Decoder 0, PHASEA input
TA0 — Timer A, Channel 0
Port B GPIO — This GPIO pin can be individually programmed as
an input or output pin.
Clock Output - can be used to monitor the internal oscillator clock
signal (see Part 6.5.7 CLKO Select Register, SIM_CLKOSR).
In the 56F8323, the default state after reset is PHASEA0.
In the 56F8123, the default state is not one of the functions offered
and must be reconfigured.
Table 2-2 Signal and Package Information for the 64-Pin LQFP
Signal Name
Pin No.
Type
State During
Reset
Signal Description
相關PDF資料
PDF描述
MC68020CFC25E 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132
MC68020CFC25E 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132
MC6804J1P 8-BIT, MROM, MICROCONTROLLER, PDIP20
MC6805S3VP 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28
MC6805S3P 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28
相關代理商/技術參數
參數描述
MC56F8323MFBE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8323VFB60 功能描述:數字信號處理器和控制器 - DSP, DSC 60MHz 60MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8323VFBE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8335 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controller
MC56F8335E 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controller