- 您現在的位置：買賣IC網 > PDF目錄1948 > MC68711E20VFNE2 (Freescale Semiconductor)IC MCU 8BIT 52-PLCC PDF資料下載
參數資料
| 型號： | MC68711E20VFNE2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 130/138頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 8BIT 52-PLCC |
| 標準包裝： | 23 |
| 系列： | HC11 |
| 核心處理器： | HC11 |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 連通性： | SCI，SPI |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 38 |
| 程序存儲器容量： | 20KB（20K x 8） |
| 程序存儲器類型： | OTP |
| EEPROM 大?。?/td> | 512 x 8 |
| RAM 容量： | 768 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 數據轉換器： | A/D 8x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 105°C |
| 封裝/外殼： | 52-LCC（J 形引線） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁當前第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
Output Compare (OC)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
91
8.4 Output Compare (OC)
Use the output compare (OC) function to program an action to occur at a specific time — when the 16-bit
counter reaches a specified value. For each of the five output compare functions, there is a separate
16-bit compare register and a dedicated 16-bit comparator. The value in the compare register is
compared to the value of the free-running counter on every bus cycle. When the compare register
matches the counter value, an output compare status flag is set. The flag can be used to initiate the
automatic actions for that output compare function.
To produce a pulse of a specific duration, write to the output compare register a value representing the
time the leading edge of the pulse is to occur. The output compare circuit is configured to set the
appropriate output either high or low, depending on the polarity of the pulse being produced. After a match
occurs, the output compare register is reprogrammed to change the output pin back to its inactive level
at the next match. A value representing the width of the pulse is added to the original value, and then is
written to the output compare register. Because the pin state changes occur at specific values of the
free-running counter, the pulse width can be controlled accurately at the resolution of the free-running
counter, independent of software latencies. To generate an output signal of a specific frequency and duty
cycle, repeat this pulse-generating procedure.
There are four 16-bit read/write output compare registers: TOC1, TOC2, TOC3, and TOC4, and the
TI4/O5 register, which functions under software control as either IC4 or OC5. Each of the OC registers is
set to $FFFF on reset. A value written to an OC register is compared to the free-running counter value
during each E-clock cycle. If a match is found, the particular output compare flag is set in timer interrupt
flag register 1 (TFLG1). If that particular interrupt is enabled in the timer interrupt mask register 1
(TMSK1), an interrupt is generated. In addition to an interrupt, a specified action can be initiated at one
or more timer output pins. For OC5–OC2, the pin action is controlled by pairs of bits (OMx and OLx) in
the TCTL1 register. The output action is taken on each successful compare, regardless of whether the
OCxF flag in the TFLG1 register was previously cleared.
OC1 is different from the other output compares in that a successful OC1 compare can affect any or all
five of the OC pins. The OC1 output action taken when a match is found is controlled by two 8-bit registers
with three bits unimplemented: the output compare 1 mask register, OC1M, and the output compare 1
data register, OC1D. OC1M specifies which port A outputs are to be used, and OC1D specifies what data
is placed on these port pins.
8.4.1 Timer Output Compare Registers
All output compare registers are 16-bit read-write. Each is initialized to $FFFF at reset. If an output
compare register is not used for an output compare function, it can be used as a storage location. A write
to the high-order byte of an output compare register pair inhibits the output compare function for one bus
cycle. This inhibition prevents inappropriate subsequent comparisons. Coherency requires a complete
16-bit read or write. However, if coherency is not needed, byte accesses can be used.
For output compare functions, write a comparison value to output compare registers TOC1–TOC4 and
TI4/O5. When TCNT value matches the comparison value, specified pin actions occur.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68882RC50A | IC COPROCESSOR FLOAT PT 68-PGA |
| MC68908GR16CFJE | IC MCU 16K FLASH 8MHZ SPI 32LQFP |
| MC68E360ZQ25VLR2 | IC MPU QUICC 32BIT 357-PBGA |
| MC68EC000EI8R2 | IC MPU 32BIT 85MHZ 68-PLCC |
| MC68EC030FE25CB1 | IC MPU 32BIT ENH 25MHZ 132-CQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC6875 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT) |
| MC6875A | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT) |
| MC6875AL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:CLOCK GENERATOR/DRIVER (SCHOTTKY MONOLITHIC INTEGRATED CIRCUIT) |
| MC6875L | 制造商:MOTOROLA 功能描述:IC |
| MC688 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INTEGRATED CIRCUITS |
發布緊急采購，3分鐘左右您將得到回復。