- 您現在的位置：買賣IC網 > PDF目錄45226 > MC68HC11A8BMP2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48 PDF資料下載
參數資料
| 型號： | MC68HC11A8BMP2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48 |
| 封裝： | PLASTIC, DIP-48 |
| 文件頁數： | 125/158頁 |
| 文件大?。?/td> | 3803K |
| 代理商： | MC68HC11A8BMP2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁當前第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
ANALOG-TO-DIGITAL CONVERTER
MOTOROLA
TECHNICAL DATA
7-5
7
7.7 A/D Result Registers 1, 2, 3, and 4 (ADR1, ADR2, ADR3, and ADR4)
The A/D result registers are read-only registers used to hold an 8-bit conversion result.
Writes to these registers have no effect. Data in the A/D result registers is valid when
the CCF flag bit in the ADCTL register is set, indicating a conversion sequence is com-
plete. If conversion results are needed sooner refer to Figure 7-1. For example the
ADR1 result is valid 33 cycles after an ADCTL write. Refer to the A/D channel assign-
ments in Table 7-1 for the relationship between the channels and the result registers.
7.8 A/D Power-Up and Clock Select
A/D power-up is controlled by bit 7 (ADPU) of the OPTION register. When ADPU is
cleared, power to the A/D system is disabled. When ADPU is set, the A/D system is
enabled. A delay of as much as 100 microseconds is required after turning on the A/
D converter to allow the analog bias voltages to stabilize.
Clock select is controlled by bit 6 (CSEL) of the OPTION register. When CSEL is
cleared, the A/D system uses the system E clock. When CSEL is set, the A/D system
uses an internal R-C clock source, which runs at about 1.5 MHz. The MCU E clock is
not suitable to drive the A/D system if it is operating below 750 kHz, in which case the
R-C internal clock should be selected. A delay of 10 ms is required after changing
CSEL from zero to one to allow the R-C oscillator to start and internal bias voltages to
settle. Refer to 9.1.5 Configuration Options Register (OPTION) for additional infor-
mation. Note that the CSEL control bit also enables a separate R-C oscillator to drive
the EEPROM charge pump.
When the A/D system is operating with the MCU E clock, all switching and comparator
operations are synchronized to the MCU clocks. This allows the comparator results to
be sampled at quiet clock times to minimize noise errors. The internal R-C oscillator is
asynchronous to the MCU clock so noise will affect A/D results more while CSEL = 1.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11A0CFU2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC11A0CP2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48 |
| MC68HC11A8BCFN2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC11A8BVP2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48 |
| MC68HC11A0CFN2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11A8BVP2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
| MC68HC11A8FN | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers |
| MC68HC11A8FN1 | 制造商:Motorola Inc 功能描述: |
| MC68HC11A8MCFN2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
| MC68HC11A8P1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。