參數資料
型號： MC68HC16Y1
廠商： Motorola, Inc.
英文描述： 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述： 16位微控制器模塊（16位模塊化微控制器）
文件頁數： 108/122頁
文件大?。?/td> 749K
代理商： MC68HC16Y1
MOTOROLA
108
MC68HC16Y1
MC68HC16Y1TS/D
Each SCCR0 contains the baud rate selection field. Baud rate must be set before the SCI is enabled.
The CPU can read and write this register at any time.
Bits [15:13] — Not Implemented
SCBR — Baud Rate
SCI baud rate is programmed by writing a 13-bit value to this field. Writing a value of zero to BR disables
the baud rate generator.
The SCI receiver operates asynchronously. An internal clock is necessary to synchronize with an in-
coming data stream. The SCI baud rate generator produces a receiver sampling clock with a frequency
16 times that of the expected baud rate of the incoming data. The SCI determines the position of bit
boundaries from transitions within the received waveform, and adjusts sampling points to the proper po-
sitions within the bit period. Receiver sampling rate is always 16 times the frequency of the SCI baud
rate, which is calculated as follows:
SCI Baud Rate = System Clock/(32
BR)
where BR is in the range {1, 2, 3, ..., 8191}.
Each SCCR1 contains SCI configuration parameters. The CPU can read and write this register at any
time. The SCI can modify RWU in some circumstances. In general, interrupts enabled by these control
bits are cleared by reading SCSR, then reading (receiver status bits) or writing (transmitter status bits)
SCDR.
SCCR1A/B15 — Not Implemented
LOOPS — Loop Mode
0 = Normal SCI operation, no looping, feedback path disabled
1 = Test SCI operation, looping, feedback path enabled
LOOPS controls a feedback path on the data serial shifter. When loop mode is enabled, SCI transmitter
output is fed back into the receive serial shifter. TXD is asserted (idle line). Both transmitter and receiver
must be enabled prior to entering loop mode.
WOMS — Wired-OR Mode for SCI Pins
0 = If configured as an output, TXD is a normal CMOS output.
1 = If configured as an output, TXD is an open-drain output.
WOMS determines whether the TXD pin is an open-drain output or a normal CMOS output. This bit is
used only when TXD is an output. If TXD is used as a general-purpose input pin, WOMS has no effect.
ILT — Idle-Line Detect Type
0 = Short idle-line detect (start count on first one)
1 = Long idle-line detect (start count on first one after stop bit(s))
SCCR0A, SCCR0B
— SCI Control Register 0
$YFFC18, $YFFC28
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
SCBR
RESET:
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
SCCR1A, SCCR1B
— SCI Control Register 1
$YFFC1A, $YFFC2A
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
LOOPS WOMS
ILT
PT
PE
M
WAKE
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
RESET:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68HC16Z1 16-Bit Modular Microcontroller(16位模塊化微控制器)
MC68HC24 Port Replacement Unit (PRU)
MC68HC24D Port Replacement Unit (PRU)
MC68HC705J Microcontrollers
MC68HC705K1 8-Bit Microcontroller Units (MCU).(8位微控制器)
相關代理商/技術參數
參數描述
MC68HC16Z1CAG 制造商:Freescale Semiconductor 功能描述:
MC68HC16Z1CAG16 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68HC16Z1CAG16 制造商:Freescale Semiconductor 功能描述:IC16-BIT MICROCONTROLLER
MC68HC16Z1CAG20 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68HC16Z1CAG20 制造商:Freescale Semiconductor 功能描述:Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*