參數資料
型號: MC68HC16Y1
廠商: Motorola, Inc.
英文描述: 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述: 16位微控制器模塊(16位模塊化微控制器)
文件頁數: 117/122頁
文件大小: 749K
代理商: MC68HC16Y1
MC68HC16Y1
MC68HC16Y1TS/D
MOTOROLA
117
The MRM can also operate in a special emulator mode that simplifies emulation of the array by an ex-
ternal device. Emulation mode is enabled by the EMUL bit in the MRMCR. EMUL state is determined
by the state of the DATA10 and DATA13 lines during reset. If both data lines are held low, EMUL is set,
and ROM emulation mode is enabled.
While emulation mode is enabled, the internal module chip select signal (CSM) is asserted whenever a
valid access to an address assigned to the masked ROM module is made. To be valid, an access must
be within the range specified by the ROM base array registers and must meet the address space re-
quirements defined by the ASPC field in MRMCR. CSM is asserted for all valid read accesses; it is as-
serted for write accesses only in background debug mode. The MRM does not acknowledge an access
on the IMB while in emulation mode — this causes the SCIM to run an external bus cycle. The CSM
signal is asserted on the falling edge of AS. Internal DSACK is generated by the ROM module after it
has inserted the number of wait states specified by the WAIT field in the MRMCR.
9.1 Masked ROM Control Registers
The 32-byte control register block contains registers that are used to configure the MRM and to control
ROM array function. Configuration information is specified and programmed at the same time as the
ROM content.
*Reset state of STOP = DATA14. Reset state of EMUL = (DATA10
DATA13).
STOP — Stop Bit
0 = Normal ROM operation
1 = Disable ROM and activate emulator mode if enabled
Reset state of STOP is the complement of DATA14 state during reset. ROM array base address cannot
be changed unless STOP is set.
BOOT — Boot ROM Control Bit
0 = CPU16 accesses ROM array addresses after reset
1 = CPU16 cannot access ROM array addresses after reset
Reset state of BOOT is specified by the user. Bootstrap function is overridden if STOP = 1.
LOCK — Lock Registers Bit
0 = Write lock disabled; protected registers and fields can be written
1 = Write lock enabled; protected registers and fields cannot be written
Reset state of LOCK is specified by the user. LOCK protects the ASPC and WAIT fields, as well as the
ROMBAL and ROMBAH registers. ASPC, ROMBAL and ROMBAH are also protected by the STOP bit.
EMUL — Emulator Mode Control Bit
0 = Normal ROM operation
1 = MRM enters emulator mode when STOP is set.
Reset state of EMUL is the complement of DATA10 and DATA13 state during reset. When EMUL is set,
the MRM responds to accesses by asserting the CSM signal.
MRMCR
— Masked ROM Module Configuration Register
$YFF820
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
STOP
0
0
BOOT
LOCK
EMUL
ASPC
WAIT
0
0
0
0
0
0
RESET:
*
0
0
USER
SPEC
USER
SPEC
*
USER
SPEC
USER
SPEC
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68HC16Z1 16-Bit Modular Microcontroller(16位模塊化微控制器)
MC68HC24 Port Replacement Unit (PRU)
MC68HC24D Port Replacement Unit (PRU)
MC68HC705J Microcontrollers
MC68HC705K1 8-Bit Microcontroller Units (MCU).(8位微控制器)
相關代理商/技術參數
參數描述
MC68HC16Z1CAG 制造商:Freescale Semiconductor 功能描述:
MC68HC16Z1CAG16 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68HC16Z1CAG16 制造商:Freescale Semiconductor 功能描述:IC16-BIT MICROCONTROLLER
MC68HC16Z1CAG20 功能描述:16位微控制器 - MCU 16 BIT MCU 1K RAM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68HC16Z1CAG20 制造商:Freescale Semiconductor 功能描述:Microcontroller