參數資料
型號： MC8610PX1066JB
廠商： Freescale Semiconductor
文件頁數： 85/96頁
文件大?。?/td> 0K
描述： MPU E600 CORE 1066MHZ 783-PBGA
標準包裝： 36
系列： MPC86xx
處理器類型： 32-位 MPC86xx PowerPC
速度： 1.066GHz
電壓： 1V
安裝類型： 表面貼裝
封裝/外殼： 783-BBGA，F(xiàn)CBGA
供應商設備封裝： 783-FCPBGA（29x29）
包裝： 托盤
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
86
Tyco Electronics
800-522-6752
Chip Coolers
P.O. Box 3668
Harrisburg, PA 17105-3668
Internet: www.chipcoolers.com
Wakefield Engineering
603-635-5102
33 Bridge St.
Pelham, NH 03076
Internet: www.wakefield.com
Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air
velocity, spatial volume, mass, attachment method, assembly, and cost.
3.12.2.1
Internal Package Conduction Resistance
For the exposed-die packaging technology described in Table 62, the intrinsic conduction thermal resistance paths are as
follows:
The die junction-to-case thermal resistance
The die junction-to-board thermal resistance
Figure 55 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board.
Figure 55. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is conducted through the
silicon, then through the heat sink attach material (or thermal interface material), and finally to the heat sink. The
junction-to-case thermal resistance is low enough that the heat sink attach material and heat sink thermal resistance are the
dominant terms.
3.12.2.2
Thermal Interface Materials
A thermal interface material is recommended at the package-to-heat sink interface to minimize the thermal contact resistance.
Figure 56 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, fluoroether oil),
a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal
interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface
thermal resistance. In contrast, the bare joint results in a thermal resistance approximately seven times greater than the thermal
grease joint.
External Resistance
Internal Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
(Note the internal versus external package resistance.)
相關PDF資料
PDF描述
345-012-523-204 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-202 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-201 CARDEDGE 12POS DUAL .100 GREEN
345-012-521-804 CARDEDGE 12POS DUAL .100 GREEN
345-012-521-802 CARDEDGE 12POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
MC8610PX1066JZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610PX1067G 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610PX1067J 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610PX1333JB 功能描述:微處理器 - MPU REV 1.1 8610 1.025V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC8610PX1333JZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*