參數資料
型號： MCZ33889BEG
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： System Basis Chip with Low Speed Fault Tolerant CAN Interface
中文描述： 系統基礎芯片與低速容錯CAN接口
文件頁數： 25/60頁
文件大?。?/td> 705K
代理商： MCZ33889BEG
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
33889
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
MASTER IN/SLAVE OUT (MISO
MISO is the Master In Slave Out pin of the serial peripheral
interface. Data is sent from the SBC to the microcontroller
through the MISO pin.
MASTER OUT/SLAVE IN (MOSI)
MOSI is the Master Out Slave In pin of the serial peripheral
interface. Control data from a microcontroller is received
through this pin.
CHIP SELECT (CS)
CS is the Chip Select pin of the serial peripheral interface.
When this pin is LOW, the SPI port of the device is selected.
WATCH DOG (WDOG)
The Watchdog output pin is asserted LOW to flag that the
software watchdog has not been properly triggered.
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
DEVICE SUPPLY
The device is supplied from the battery line through the
VSUP pin. An external diode is required to protect against
negative transients and reverse battery. It can operate from
4.5 V and under the jump start condition at 27 V DC. This pin
sustains standard automotive voltage conditions such as
load dump at 40 V. When V
SUP
falls below 3.0 V typical, the
MC33889 detects it and stores the information in the SPI
register, in a bit called “BATFAIL”. This detection is available
in all operation modes.
VDD1 VOLTAGE REGULATOR
VDD1 Regulator is a 5.0 V output voltage with total current
capability of 200 mA. It includes a voltage monitoring circuitry
associated with a reset function. The VDD1 regulator is fully
protected against overcurrent, short-circuit and has
overtemperature detection warning flags and shutdown with
hysteresis.
V2 REGULATOR
V2 Regulator circuitry is designed to drive an external path
transistor in order to increase output current flexibility. Two
pins are used: V2 and V2CTRL. Output voltage is 5.0 V and
is realized by a tracking function of the VDD1 regulator. A
recommended ballast transistor is the MJD32C. Other
transistors might be used, however depending upon the PNP
gain, an external resistor capacitor network might be
connected between the emitter and base of the PNP. The use
of external ballast is optional (refer to simplified typical
application). The state of V2 is reported into the IOR register
(if V2 is below 4.5 V typical, or in cases of overload or short-
circuit).
HS1 VBAT SWITCH OUTPUT
HS1 output is a 2.0 ohm typical switch from the VSUP pin.
It allows the supply of external switches and their associated
pullup or pull-down circuitry, for example, in conjunction with
the wake-up input pins. Output current is limited to 200 mA
and HS1 is protected against short-circuit and has an over
temperature shutdown (reported into the IOR register). The
HS1 output is controlled from the internal register and the
SPI. It can be activated at regular intervals in sleep mode
thanks to an internal timer. It can also be permanently turned
on in normal or stand-by modes to drive external loads, such
as relays or supply peripheral components. In case of
inductive load drive, external clamp circuitry must be added.
SPI
The complete device control as well as the status report is
done through an 8 bit SPI interface. Refer to the SPI
paragraph.
CAN
The device incorporates a low speed fault tolerant CAN
physical interface. The speed rate is up to 125 kBauds.
The state of the CAN interface is programmable through
the SPI. Reference the
CAN transceiver description on page
30
.
PACKAGE AND THERMAL CONSIDERATION
The device is proposed in a standard surface mount SO28
package. In order to improve the thermal performances of the
SO28 package, 8 pins are internally connected to the lead
frame and are used for heat transfer to the printed circuit
board.
相關PDF資料
PDF描述
MCZ33927EK Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod
MCZ33970EG Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms
MCZ33976EG Dual Gauge Driver with Configurable esponse Time
MCZ33977EG Single Gauge Driver
MCZ33989EG System Basis Chip with High-Speed CAN Transceiver
相關代理商/技術參數
參數描述
MCZ33889BEG 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER
MCZ33889BEG/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:System Basis Chip with Low Speed Fault Tolerant CAN Interface
MCZ33889BEGR2 功能描述:網絡控制器與處理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33889DEG 功能描述:網絡控制器與處理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33889DEG 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*