- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33889BEG (飛思卡爾半導體(中國)有限公司) System Basis Chip with Low Speed Fault Tolerant CAN Interface PDF資料下載
參數資料
| 型號： | MCZ33889BEG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| 中文描述： | 系統基礎芯片與低速容錯CAN接口 |
| 文件頁數： | 31/60頁 |
| 文件大小： | 705K |
| 代理商： | MCZ33889BEG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Receiver Function
In normal operation (no bus failures), RX is the image of
the differential bus voltage. The differential receiver inputs
are connected to CANH and CANL.
The device incorporates single ended comparators
connected to CANH and CANL in order to monitor the bus
state as well as detect bus failures. Failures are reported via
the SPI.
In normal operation when no failure is present, the
differential comparator is active. Under a fault condition, one
of the two CANH or CANL pins can be become non-
operational. The single ended comparator of either CANH or
CANL is activated and continues to report a bus state to Rx
pin. The device permanently monitors the bus failure and
recovery, and as soon as fault disappears, it automatically
switches back to differential operation.
CAN interface operation Mode
The CAN has 3 operation modes: TxRx (Transmit-
Receive), Receive Only, and Term-VBAT (Terminated to
VBAT). The mode is selected by the SPI. As soon as the
MC33889 mode is sleep or stop (selected via MCR register),
the CAN interface automatically enters Tem-Vbat mode.
Tx Rx mode:
In this mode, the CAN drivers and receivers are enabled,
and the device is able to send and receive messages. Bus
failures are detected and managed, this means that in case
of a bus failure, one of the CAN drivers can be disabled, but
communication continues via the remaining drivers.
Receive Only mode:
In this mode, the transmitter path is disabled, so the device
does not drive the bus. It maintains CANL and CANH in the
recessive state. The receiver function operates normally.
TermVbat mode:
In this mode, the transmitter and receiver functions are
disabled. The CANL pin is connected to V
SUP
through the
RTL resistor and internal pull up resistor of 12.5kOhms. In
this mode, the device monitors the bus activity and if a wake
up conditions is encountered on the CAN bus, it will wakes up
the MC33889.
The device will enter into a normal request mode if low
power mode was in sleep, or generates an INT. It enters into
Normal request mode if low power mode was in stop mode.
If the device was in normal or stand by mode, the Rx pin will
report a wake up (feature not available on the MC33889B).
See Rx pin behavior.
Bus Failure Detection
General description:
The device permanently monitors the bus lines and
detects faults in normal and receive only modes. When a fault
is detected, the device automatically takes appropriate
actions to minimize the system current consumption and to
allow communication on the network. Depending on the type
of fault, the mode of operation, and the fault detected, the
device automatically switches off one or more of the following
functions: CANL or CANH line driver, RTL or RTH termination
resistors, or internal switches. These actions are detailed in
the following table.
The device permanently monitors the faults and in case of
fault recovery, it automatically switches back to normal
operation and reconnects the open functions. Fault detection
and recovery circuitry have internal filters and delays timing,
detailed in the AC characteristics parameters.
The failure list identification and the consequence on the
device operation are described in following table. The failure
detection, and recovery principle, the transceiver state after a
failure detected, timing for failure detection and recovery can
be found in the ISO11898-3 standard.
The following table is a summary of the failure
identifications and of the consequences on the CAN driver
and receiver when the CAN is in Tx Rx mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33927EK | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
| MCZ33977EG | Single Gauge Driver |
| MCZ33989EG | System Basis Chip with High-Speed CAN Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33889BEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
| MCZ33889BEG/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33889BEGR2 | 功能描述:網絡控制器與處理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33889DEG | 功能描述:網絡控制器與處理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33889DEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
發布緊急采購，3分鐘左右您將得到回復。