- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33991EG (飛思卡爾半導體(中國)有限公司) Gauge Driver Integrated Circuit PDF資料下載
參數資料
| 型號： | MCZ33991EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Gauge Driver Integrated Circuit |
| 中文描述： | 儀表驅動集成電路 |
| 文件頁數： | 31/36頁 |
| 文件大?。?/td> | 481K |
| 代理商： | MCZ33991EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
33991
TIMING DESCRIPTIONS AND DIAGRAMS
SAMPLE CODE
SAMPLE CODE
/* The following example code demonstrates a typical set up configuration for a M68HC912B32. */
/* This code is intended for instructional use only. Motorola assumes no liability for use or */
/* modification of this code. It is the responsibility of the user to verify all parameters, variables,*/
/* timings, etc. */
void InitGauges
(void)
{
/* Step 1 */
Command_Gauge
(0x00,0x03);
Command_Gauge
(0x00,0x08);
/* 8 uSec calibration */
PORTS = 0x00;
For
(cnt = 0; cnt < 5; cnt++)
{
NOP;
}
PORTS = 0x04;
/* Step 2 */
Command_Gauge
(0xA0,0x21);
Command_Gauge
(0x10,0x00);
/*Check SO bits for Out of Range Clock Calibration */
If
((status & 0x80) != 0)
/*If Clock is out of range then recalibrate 8 uSec pulse */
/* Step 3 */
Command_Gauge
(0x40,0x18);
/* Step 4 */
Command_Gauge
(0x60,0x18);
/* Check SO bit ST4 to see if Gauge 0 has moved */
If
((status & 0x10) != 0)
/* If ST4 is logic 1 then Gauge 0 has moved to the first microstep */
/* Step 5 */
Command_Gauge
(0x10,0x00);
/* Check SO bit ST4 to see if Gauge 0 has moved */
If
((status & 0x10) != 0)
/* If it has moved, then keep track of position */
/* Wait until 24 steps are finished then send a RTZ command (Step 7) */
/* Step 6 */
Command_Gauge
(0x80,0x02);
/* Step 7 */
Command_Gauge
(0x10,0x00);
/* Read Status until RTZ is done */
While
((status & 0x04) != 0)
{
Command_Gauge
(0x10,0x00);}
/* Enable Gauges */
/* Clock Cal bit set */
/* Enable GDIC CS pin - PORTS2 */
/* Wait for 8 uSec calibration */
/* Disable GDIC CS pin - PORTS2 */
/* Send RTZCR values */
/* Null Read to get SO status */
/* Send position to gauge0 */
/* Send position to gauge1 */
/* Null Read to get SO status */
/* Send RTZ to Gauge 0 */
/* Null Read to get status */
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33993EW | Multiple Switch Detection Interface |
| MCZ33996EK | 16-Output Switch with SPI Control |
| MCZ34652EF | 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
| MCZ34701EWR2 | 1.5A Switch-Mode Power Supply with Linear Regulator |
| MCZ79076EG | Electronic Ignition Control Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33991EGR2 | 功能描述:馬達/運動/點火控制器和驅動器 GAUGE DRIVER IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33993EW | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33993EWR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33996CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk |
| MCZ33996CEKR2 | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。