- 您現在的位置：買賣IC網 > PDF目錄377972 > ML6440 (Fairchild Semiconductor Corporation) Multi-Standard 8-bit Adaptive Digital Input Comb Filter(多標準8位自適應數字輸入組合濾波器) PDF資料下載
參數資料
| 型號： | ML6440 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Multi-Standard 8-bit Adaptive Digital Input Comb Filter(多標準8位自適應數字輸入組合濾波器) |
| 中文描述： | 多標準的8位數字輸入自適應梳狀濾波器（多標準8位自適應數字輸入組合濾波器） |
| 文件頁數： | 10/18頁 |
| 文件大?。?/td> | 227K |
| 代理商： | ML6440 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
ML6440
10
to the video content of the last 60+ lines (frames) of video
—a frame weighing function— to determine the best
filtering approach of the current video content. Finally, 1
of 7 thresholds can be chosen to adjust either real-time
(automatically) by the ML6440 itself or fixed manually by
design. An internal 12-bit analysis is used for the filtering
algorithm. An additional fader circuit is included to
"smooth" the transitions between comb and notch filtering.
In NTSC, every other line of chroma is inverted while
there are no changes in luma (assuming there is no change
in color between adjacent lines). This permits data to be
added from the first stored line of data with the third line
of active high-band video data, each with a scaling of
0.25, and add the second stored line of data with a scaling
of 0.50. The result contains no chroma, only luma
information. Subtracting this information from the high-
band signal yields only chroma information.
In PAL, each line of data rotates the phase of the chroma
by 90 degrees. Therefore, by adding the first line of stored
high-band information from the active third line, the
chroma is canceled, leaving only luma information. Once
again, this information is subtracted with the appropriate
amplitude scaling from the original highband information
to yield only chroma.
In bandsplit (notch) filtering and luma peaking, the digital
bandsplit filter is used as an alternate filter when the
SmartComb algorithm determines that the comb filter
output signal would be contaminated with cross chroma
artifacts. To maintain a reasonable amount of apparent
resolution in the luminance signal, luma peaking is
applied. This helps maintain image quality in the portion
of the video image where comb filtering would generate
artifacts.
The ML6440 SmartComb provides a real-time filtering
algorithm solution (automatic mode) for a wide variety of
video sources without the shortcomings of using fixed
thresholds (manual mode). The automatic threshold
tracking circuit responds quickly, adjusting itself in about
1/300th of a second (about 60 lines). The transition from
the comb to the digital bandsplit is made with a
continuous digital fader to prevents switching glitches.
The bandsplit-notch and comb filters were designed to
reduce color bar peak-to-peak dot edge crawl to <7.5%
for 75% color bars. Peak-to-peak cross color on the white
bar edge was designed to be <1% with 75% color bars.
SERIAL PROGRAM MODE
In Serial Program Mode, the comb filter can be controlled
with the serial interface. Control inputs may be clocked in
serially with S DATA and S CLK , when
S
/P is low. Serial
bus transfers require an 8-bit address followed by 8-bits of
data for the internal data register. The pattern is described
in Tables 1 through 5.
The serial bus control in the ML6440 has one level of
addressing followed by control register programming.
Figure 2 shows the physical waveforms generated in order
to address the ML6440. There are six basic parts of the
waveform:
1. Start indication: Clock Cycle 0
2. Device address shifted in: Clock Cycle 1 thru 8
3. Device address strobed /decoded: Clock Cycle 9
4. Data shifted in: Clock Cycle 10 thru 17
5. Data strobed to appropriate register: Clock Cycle 18
6. Stop indication: Clock Cycle 19
PARALLEL PROGRAM MODE
In Parallel Program Mode, the CI/DI[7:0] pins act as
programming pins for the internal 8-bit register (D[7:0])
such that CI7/DI7=D7, CI6/DI6=D6, ... CI0/DI0=D0. In
the parallel mode, the
S
/P serves as a rising edge-triggered
strobe pin for the internal registers of D[7:0]. When
S
/P
goes from low to high, data applied to the inputs (CI/
DI[7:0]), is loaded into the internal 8-bit register D[7:0]
directly. A transition on the
S
/P pin back to low will
reactivate the serial mode. If the
S
/P is held at a high, the
serial mode is inactive.
CONTROL REGISTER, D[7:0]
The internal register, D[7:0], controls the following
functions within the ML6440. Again, this register can be
programmed through either a serial or parallel interface.
The
RST
acts as a reset pin, forcing all the bits of the
FUNCTIONAL DESCRIPTION
(Continued)
Figure 5: Reset Timing
POWER ON
AT LEAST 5μs HIGH
AT LEAST 1μs LOW
RST
相關PDF資料 |
PDF描述 |
|---|---|
| ML6460 | CCIR656 NTSC Video Encoder(CCIR656標準NTSC視頻編碼器) |
| ML6509 | Active SCSI Terminator(SCSI系統的有源終端器) |
| ML6510 | Series Programmable Adaptive Clock Manager(系列可編程自適應時鐘管理器) |
| ML6516244 | 16-Bit Buffer/Line Driver with 3-State Outputs(BiCMOS 16位緩沖器/線驅動器（三態輸出）) |
| ML6518 | 18 Line Hot-Insertable Active SCSI Terminator(線熱插入有源SCSI終端器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML6440CH | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Multi-Standard 8-bit Adaptive Digital Input Comb Filter |
| ML645PTA102MLZ | 制造商:COILCRAFT 制造商全稱:Coilcraft lnc. 功能描述:High Reliability Power Inductors |
| ML6460 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder with Macrovision |
| ML6460CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder with Macrovision |
| ML6461 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder |
發布緊急采購，3分鐘左右您將得到回復。