參數資料
型號： ML6440
廠商： Fairchild Semiconductor Corporation
英文描述： Multi-Standard 8-bit Adaptive Digital Input Comb Filter(多標準8位自適應數字輸入組合濾波器)
中文描述： 多標準的8位數字輸入自適應梳狀濾波器（多標準8位自適應數字輸入組合濾波器）
文件頁數： 11/18頁
文件大?。?/td> 227K
代理商： ML6440
ML6440
11
internal data register low (D[7:0]=0) which defaults to
automatic combing of NTSC/CCIR601 composite video.
The Y+C/CV selection bit, D7, controls whether Y+C or CV
format is the source for the comb filter. Setting this bit low
selects the composite input pins, which is combed by
default. Setting the bit high selects the Y+C inputs as the
source for video (see bypass section). This source is not
combed and the Y+C inputs are not activated until the
S
/P
pin is rising-edge triggered.
Adaption thresholds 2 through 0 are D6 through D4,
respectively. These set the adaption behavior from
automatic (D[6:4]=000) to one of seven settings ranging
from fine tuning of computer graphics to photographic
images. See Table 4.
Comb modes 1 and 0, (D3 and D2, respectively) are used
to enable and disable adaption separately on Y and C
data. For NTSC, if D[3:2]=<00>, then Y is adaptive and C
is always combed. For NTSC, if D[3:2]=<01>, both Y and
C are adaptive. For PAL, if D[3:2]=<00>, then both Y and
C are adaptive. For PAL, if D[3:2]=<01>, then Y is
adaptive and C is combed. For NTSC and PAL, if
D[3:2]=<10>, then Y and C are forced to comb mode. For
NTSC and PAL, if D[3:2]=<11>, then both Y and C are in
bandsplit filtering mode only. See Table 5.
The D1 bit sets the choice of data rates between CCIR601
and Square pixel. CCIR601 is active low. Square pixel is
active high. The last bit, D0, select the standard, NTSC or
PAL. NTSC is active low. PAL is active high. See Table 2.
The remaining pin function controls are independent of
the data register: CLK,
RST
, and OE. The CLK pin requires
a clock at the rates listed in Table 2. Its duty cycle must
meet the duration minimum for high and low.
The
RST
pin resets the comb logic including the internal
data register on active low but does not clear the line
delays. This part requires a timed reset pulse. On power
up or at any time a return to automatic combing of NTSC/
CCIR601 composite video is required the reset pin must
have been high for at least 5 micro seconds. Then taken
low for at least one micro second before returning high
again to resume normal operation. Neither pulse width
nor rise and fall times are critical.
In most applications a microprocessor will be available to
provide timing and control waveforms. It will provide this
reset pulse and if needed set the appropriate comb filter
mode. In non processor systems an R C network can
provide this reset pulse. See Figure 5.
CHROMA AND LUMA BYPASS OPERATION
This mode can be activated by setting the internal bit
D7 = 1 either through the serial or parallel programming
modes. Once the register is set (D7 = 1), the comb filter
will look at the inputs for luma on the CV[7:0] pins for a
luma bypass to the outputs of the Y[7:0] pins respectively;
as well as inputs for chroma on the CI/DI[7:0] pins for a
chroma bypass to the outputs of the C[7:0] pins
respectively. The comb filter will continue to look at the
inputs as long as D7 is set high.
Data presented to the inputs (CI/DI[7:0]) is not interrupted
in the color processing path when
S
/P is held high or low.
Therefore, it is recommended that
S
/P activity be limited to
sync or blanking intervals in the video to avoid unwanted
visual artifacts during register programming.
Clock Timing
Figure 6 depicts digital video input and output timing for
valid data.
FUNCTIONAL DESCRIPTION
(Continued)
Y OR C DATA
60%
20ns
15ns
0ns
Y OR C DATA
Y/C OUTPUT
CV INPUT
13.5MHz CLOCK
CV DATA
40%
CV DATA
Figure 6: Clock Timing
相關PDF資料
PDF描述
ML6460 CCIR656 NTSC Video Encoder(CCIR656標準NTSC視頻編碼器)
ML6509 Active SCSI Terminator(SCSI系統的有源終端器)
ML6510 Series Programmable Adaptive Clock Manager(系列可編程自適應時鐘管理器)
ML6516244 16-Bit Buffer/Line Driver with 3-State Outputs(BiCMOS 16位緩沖器/線驅動器（三態輸出）)
ML6518 18 Line Hot-Insertable Active SCSI Terminator(線熱插入有源SCSI終端器)
相關代理商/技術參數
參數描述
ML6440CH 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Multi-Standard 8-bit Adaptive Digital Input Comb Filter
ML645PTA102MLZ 制造商:COILCRAFT 制造商全稱:Coilcraft lnc. 功能描述:High Reliability Power Inductors
ML6460 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder with Macrovision
ML6460CS 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder with Macrovision
ML6461 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:NTSC Video Encoder
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*