FUNCTIONAL PIN DESCRIPTION ADC SUPPLY PINS (VDD" />
參數資料
型號： MM908E624ACDWBR2
廠商： Freescale Semiconductor
文件頁數： 9/39頁
文件大?。?/td> 0K
描述： IC TRPL SWITCH MCU/LIN 54-SOIC
標準包裝： 1,000
應用： 自動鏡像控制
核心處理器： HC08
程序存儲器類型： 閃存（16 kB）
控制器系列： 908E
RAM 容量： 512 x 8
接口： SCI，SPI
輸入/輸出數： 16
電源電壓： 5.5 V ~ 18 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 54-BSSOP（0.295"，7.50mm 寬）
包裝： 帶卷 (TR)
供應商設備封裝： 54-SOIC
配用： KIT908E624DWBEVB-ND - KIT EVAL 908E624 TRPL W/MCU/LIN
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
908E624
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
ADC SUPPLY PINS (VDDA AND VSSA)
VDDA and VSSA are the power supply pins for the analog-
to-digital converter (ADC). It is recommended that a high-
quality ceramic decoupling capacitor be placed between
these pins.
Important
VDDA is the supply for the ADC and should be
tied to the same potential as EVDD via separate traces.
VSSA is the ground pin for the ADC and should be tied to the
same potential as EVSS via separate traces.
For details, refer to the 68HC908EY16 data sheet.
ADC REFERENCE PINS (VREFL AND VREFH)
VREFL and VREFH are the reference voltage pins for the
ADC. It is recommended that a high quality ceramic
decoupling capacitor be placed between these pins.
Important
VREFH is the high reference supply for the
ADC and should be tied to the same potential as VDDA via
separate traces. VREFL is the low reference supply for the
ADC and should be tied to the same potential as VSSA via
separate traces.
For details, refer to the 68HC908EY16 data sheet.
TEST PIN (FLSVPP)
This pin is for test purposes only. Do not connect in the
application or connect to GND.
PWMIN PIN (PWMIN)
This pin is the direct PWM input for high side outputs 1 and
2 (HS1 and HS2). If no PWM control is required, PWMIN
must be connected to VDD to enable the HS1 and HS2
outputs.
LIN TRANSCEIVER OUTPUT PIN (RXD)
This pin is the output of LIN transceiver. The pin must be
connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD pin).
RESET PIN (RST_A)
RST_A
is the reset output pin of the analog die and must
be connected to the RST pin of the MCU.
Important
To ensure proper operation, do not add any
external pull-up resistor.
INTERRUPT PIN (IRQ_A)
IRQ_A
is the interrupt output pin of the analog die
indicating errors or wake-up events. This pin must be
connected to the IRQ pin of the MCU.
WINDOW WATCHDOG CONFIGURATION PIN
(WDCONF)
This pin is the configuration pin for the internal watchdog.
A resistor is connected to this pin. The resistor value defines
the watchdog period. If the pin is open, the watchdog period
is fixed to its default value.
The watchdog can be disabled (e.g., for flash
programming or software debugging) by connecting this pin
to GND.
POWER SUPPLY PINS (VSUP1 AND VSUP2)
This VSUP1 power supply pin supplies the voltage
regulator, the internal logic, and LIN transceiver.
This VSUP2 power supply pin is the positive supply for the
high side switches.
POWER GROUND PIN (GND)
This pin is the device ground connection.
HIGH SIDE OUTPUT PINS (HS1 AND HS2)
These pins are high side switch outputs to drive loads such
as relays or lamps. Each switch is protected with over-
temperature and current limit (over-current). The output has
an internal clamp circuitry for inductive load. The HS1 and
HS2 outputs are controlled by the SPI and have a direct
enabled input (PWMIN) for PWM capability.
HIGH SIDE OUTPUT PIN (HS3)
This high side switch can be used to drive small lamps,
Hall-effect sensors, or switch pull-up resistors. The switch is
protected with over-temperature and current limit (over-
current). The output is controlled only by the SPI.
LIN BUS PIN (LIN)
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems and is based
on the LIN bus specification.
WAKE-UP PINS (L1 AND L2)
These pins are high-voltage capable inputs used to sense
external switches and to wake-up the device from Sleep or
Stop mode. During Normal mode the state of these pins can
be read through the SPI.
Important
If unused, these pins should be connected to
VSUP or GND to avoid parasitic transitions. In Low Power
Mode, this could lead to random wake-up events.
CURRENT SENSE OPERATIONAL AMPLIFIER
PINS (E+, E-, OUT, VCC)
These are the pins of the single supply current sense
operational amplifier.
The E+ and E- input pins are the non-inverting and
inverting inputs of the current sense operational
amplifier, respectively.
The OUT pin is the output pin of the current sense
operational amplifier.
The VCC pin is the +5.0 V single supply connection.
相關PDF資料
PDF描述
046232108015800+ CONN FFC/FPC 8POS 1MM VERT SMD
SST26VF032A-80-5I-QAE IC FLASH 32MBIT 8WSON
07FMN-BMTR-A-TB CONN FMN HOUSNG 7POS SGL REV SMD
MM908E624AYEWR2 IC TRPL SWITCH MCU/LIN 54-SOIC
05FMN-BMTTR-A-TB CONN FMN HSNG 5POS STAG REV SMD
相關代理商/技術參數
參數描述
MM908E624ACEW 功能描述:開關 IC - 各種 TRIPLE HIGH SIDE SW RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel
MM908E624ACEW/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers
MM908E624ACEWR2 功能描述:電源開關 IC - 配電 TRIPLE HIGH SIDE DRIVER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MM908E624ACPEW 功能描述:8位微控制器 -MCU 3 HIGH SIDE SWITCH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E624ACPEWR2 功能描述:8位微控制器 -MCU 3 HIGH SIDE DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*