參數資料
型號： MR2900
廠商： Shindengen Electric Manufacturing Company, Ltd.
英文描述： Provision for Standby mode operation Partial Resonance Power Supply IC Module
中文描述： 撥備待機模式操作局部共振電源IC模塊
文件頁數： 8/19頁
文件大?。?/td> 226K
代理商： MR2900
Shindengen Electric MFG.CO.,LTD
- 8 -
3.4 Standby Mode Control (patent applied for)
The MR2000 Series is able to switch between two methods
of output voltage control - normal operation and the standby
mode, in a single power supply.
The standby mode supported by this IC employs the burst
method for intermittent operation under light loads to
reduce oscillation frequency and switching losses, and is
effective in reducing the standby input voltage under
micro-loads.
A unique characteristic of this IC is the use of the burst
mode for intermittent operation without stopping IC control,
and thus minimizing output ripple.
The Z/C pin is clamped to a voltage of 4.5V (typical) or less
by an external signal to allow selection of standby mode
control. The standby mode is cleared (ie restored to the
normal mode) by clearing the clamp voltage on the Z/C pin,
and applying a voltage of 4.5V (typical) or higher.
In normal operation the ON range of the main switching
device is controlled in a linear manner in relation to voltage
variation at the F/B pin, while in standby mode operation the
Emitter/OCL pin current detection threshold value is
switched from 0.6V for the normal mode to 0.05V for the
standby mode.
The collector current is fixed at a peak value by the current
detection threshold value, and the burst mode is selected.
Burst mode control is such that oscillation occurs when the
voltage at the F/B pin is 1.8V (typical) or higher, and is
stopped when this voltage is 0.8V (typical) or lower.
As output voltage control in the standby mode fixes the
drain current peak value for each oscillation cycle, the duty
ratio of the oscillating and non-oscillating intervals is varied to ensure a constant voltage.
Fig.3.5 Standby Mode Control
Fig.3.6 Standby Mode Control Sequence
Fig.3.7 Standby Signal Receive Sequence
2
7
1
3
Z/C pin
Drain pin
Emitter/OCL
pin
Output voltage error
detection feedback
signal
4.5V
(TYP)
6
Standby signal
(external signal)
F/B pin
Switched from
0.6V to 0.05V
V
F/B(burst start)
=1.8V
【
V
F/B
】
【
I
C
】
【
V
OUT
ripple
】
V
F/B(burst stop)
=0.8V
【
V
Z/C
】
【
I
C
】
【
I
OUT
】
Standby mode
Normal operation
Normal
operation
0.2V
4.5V(TYP)
Standby mode start
Standby mode clear
相關PDF資料
PDF描述
MR2920 Provision for Standby mode operation Partial Resonance Power Supply IC Module
MR2940 Provision for Standby mode operation Partial Resonance Power Supply IC Module
MS52C181A 131,072-Word × 8-Bit STATIC RAM +1,048,576-Word × 8-Bit One Time PROM(128k字×8位靜態RAM+1M字×8位 OTPROM)
MS52C182A 65,536-Word × 16-Bit or 131,072-Word × 8-Bit STATIC RAM +524,288-Word × 16-Bit or 1,048,576-Word × 8-Bit One Time PROM(64k字×16位或128k字×8位靜態RAM+512k字×16位或1M字×8位 OTPROM)
MS81V06160 (401,408-word ⅴ 16-bit) FIFO memory
相關代理商/技術參數
參數描述
MR29-0R2011 制造商:Alpha 3 Manufacturing 功能描述:
MR29-0R2022 制造商:Alpha 3 Manufacturing 功能描述:
MR29-0R2223 制造商:Alpha 3 Manufacturing 功能描述:
MR29-0R2227 制造商:Alpha 3 Manufacturing 功能描述:
MR291.04D 制造商:IVO 制造商全稱:Baumer IVO GmbH & Co. KG 功能描述:Accessories & Service
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*