參數(shù)資料
型號: MR80C32E-16P883
廠商: TEMIC SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
文件頁數(shù): 95/176頁
文件大小: 2962K
代理商: MR80C32E-16P883
25
2535J–AVR–08/10
ATtiny13
When this clock source is selected, start-up times are determined by the SUT fuses as shown in
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation. Refer to “System Clock Prescaler” on page
26 for details.
6.2.2
Calibrated Internal 4.8/9.6 MHz Oscillator
The calibrated internal oscillator provides a 4.8 or 9.6 MHz clock source. The frequency is nomi-
nal at 3V and 25
°C. If the frequency exceeds the specification of the device (depends on V
CC),
the CKDIV8 fuse must be programmed so that the internal clock is divided by 8 during start-up.
The internal oscillator is selected as the system clock by programming the CKSEL fuses as
shown in Table 6-4. If selected, it will operate with no external components.
Note:
1. The device is shipped with this option selected.
During reset, hardware loads the calibration data into the OSCCAL register and thereby auto-
matically calibrates the oscillator. There are separate calibration bytes for 4.8 and 9.6 MHz
operation but only one is automatically loaded during reset (see section “Calibration Bytes” on
page 104). This is because the only difference between 4.8 MHz and 9.6 MHz mode is an inter-
nal clock divider.
By changing the OSCCAL register from SW, see “OSCCAL – Oscillator Calibration Register” on
page 27, it is possible to get a higher calibration accuracy than by using the factory calibration.
When this oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section “Calibration Bytes” on page 104.
Table 6-3.
Start-up Times for the External Clock Selection
SUT1..0
Start-up Time from
Power-down and Power-save
Additional Delay
from Reset
Recommended
Usage
00
6 CK
14CK
BOD enabled
01
6 CK
14CK + 4 ms
Fast rising power
10
6 CK
14CK + 64 ms
Slowly rising power
11
Reserved
Table 6-4.
Internal Calibrated RC Oscillator Operating Modes
CKSEL1..0
Nominal Frequency
10(1)
9.6 MHz
01
4.8 MHz
相關PDF資料
PDF描述
MR80C32E-16P883 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MQ83C154DCXXX-25P883D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MR80C52EXXX-25:RD 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
MIP7365-450F17I 64-BIT, 450 MHz, MICROPROCESSOR, CQFP208
MIP7365-450B1M 64-BIT, 450 MHz, MICROPROCESSOR, PBGA256
相關代理商/技術參數(shù)
參數(shù)描述
MR80C51BH 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space
MR80C86 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor
MR80C86/B 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:Microprocessor, 16 Bit, 44 Pin, Ceramic, LCC
MR80C86-2 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor
MR80C86-2/883 制造商:Rochester Electronics LLC 功能描述:- Bulk