- 您現在的位置：買賣IC網 > PDF目錄385639 > MT48LC2M32LFFC (Micron Technology, Inc.) 512K x 32 x 4 banks 3.3v SDRAM(3.3V,512K x 32 x 4組同步動態RAM) PDF資料下載
參數資料
| 型號： | MT48LC2M32LFFC |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | 512K x 32 x 4 banks 3.3v SDRAM(3.3V,512K x 32 x 4組同步動態RAM) |
| 中文描述： | 為512k × 32 × 4銀行3.3V的內存電壓（3.3V，512K采樣× 32 × 4組同步動態RAM）的 |
| 文件頁數： | 5/50頁 |
| 文件大?。?/td> | 1054K |
| 代理商： | MT48LC2M32LFFC |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
5
64Mb: x32, 3.3V SDRAM
BatRam_3V.p65 – Rev. 0.7, Pub. 2/01
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2001, Micron Technology, Inc.
64Mb: x32, 3.3V
SDRAM
PRELIMINARY
BALL DESCRIPTIONS
BALL OUT
SY MBOL
TY PE
DESCRIPTION
I1
CLK
Input
Clock: CLK is driven by the system clock. All SDRAM input signals are sampled
on the positive edge of CLK. CLK also increments the internal burst counter
and controls the output registers.
Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal.
Deactivating the clock provides PRECHARGE POWER-DOWN and SELF REFRESH
operation (all banks idle), ACTIVE POWER-DOWN (row active in any bank) or
CLOCK SUSPEND operation (burst/access in progress). CKE is synchronous except
after the device enters power-down and self refresh modes, where CKE
becomes asynchronous until after exiting the same mode. The input buffers,
including CLK, are disabled during power-down and self refresh modes,
providing low standby power. CKE may be tied HIGH.
Chip Select: CS# enables (registered LOW) and disables (registered HIGH) the
command decoder. All commands are masked when CS# is registered HIGH. CS#
provides for external bank selection on systems with multiple banks. CS# is
considered part of the command code.
Command Inputs: RAS#, CAS#, and WE# (along with CS#) define the
command being entered.
Input/Output Mask: DQM is sampled HIGH and is an input mask signal for write
accesses and an output enable signal for read accesses. Input data is masked
during a WRITE cycle. The output buffers are placed in a High-Z state (two-
clock latency) when during a READ cycle. DQM0 corresponds to DQ0–DQ7,
DQM1 corresponds to DQ8–DQ15, DQM2 corresponds to DQ16–DQ23 and DQM3
corresponds to DQ24–DQ31. DQM0-3 are considered same state when
referenced as DQM.
Bank Address Input(s): BA0 and BA1 define to which bank the ACTIVE, READ,
WRITE or PRECHARGE command is being applied. These pins also provide the
op-code during a LOAD MODE REGISTER command
Address Inputs: A0–A10 are sampled during the ACTIVE command (row-
address A0–A10) and READ/WRITE command (column-address A0–A7; with A10
defining auto precharge) to select one location out of the memory array in the
respective bank. A10 is sampled during a PRECHARGE command to determine if
all banks are to be precharged (A10 HIGH) or bank selected by BA0, BA1 (LOW).
The address inputs also provide the op-code during a LOAD MODE REGISTER
command.
Data Input/Output: Data bus
I2
CKE
Input
I8
CS#
Input
I9, J7, J8
RAS#, CAS#
WE#
DQM0–3
Input
J9, J1, F2, F8
Input
I7, H8
BA0, BA1
Input
G8, G9, F7, F3, G1, G2,
G3, H1, H2, I3, G7
A0–A10
Input
O8, M7, O9, M8, N9, L8,
L7, K8, K2, L3, L2, N1, M2,
O1, M3, O2, E8, D7, D8, B9,
C8, A9, C7, A8, A2, C3, A1,
C2, B1, D2, D3, E2
E3, E7, H3, J2, J3
DQ0–DQ31
I/O
NC
–
No Connect: These pins should be left unconnected.
Pin 70 is reserved for SSTL reference voltage supply.
DQ Power: Provide isolated power to DQs for improved noise immunity.
B2, B7, C9, D9, E1, K1,
L9, M9, N2, N7
B8, B3, C1, D1, E9,
K9, M1, N8
A7, F9, K7, O7
A3, K3, F1, L1, O3
V
DD
Q
Supply
V
SS
Q
Supply
DQ Ground: Provide isolated ground to DQs for improved noise immunity.
V
DD
V
SS
Supply
Supply
Power Supply: 3.3V ±0.3V.
Ground.
相關PDF資料 |
PDF描述 |
|---|---|
| MT48LC4M16A2 | SYNCHRONOUS DRAM |
| MT48LC16M4A2 | RSD Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 24V; Output Voltage (Vdc): 3.3V; Power: 1W; 1kVDC and 3kVDC Isolation Options; Approved for Medical Applications; Suitable for Automated Assembly; 8, 10 and 12 pin Pinning Style Options; Optional Continuous Short Circuit Protected; Efficiency to 85% |
| MT48LC8M16A2 | SYNCHRONOUS DRAM |
| MT48V2M32LFFC | 512K x 32 x 4 banks 2.5V SDRAM(2.5V,512K x 32 x 4組同步動態RAM) |
| MT48V4M32LFFC | SYNCHRONOUS DRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT48LC2M3B2B51 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SDR SDRAM MT48LC2M32B2 a?? 512K x 32 x 4 Banks |
| MT48LC2M8A1 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC2M8A1TGS | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC2M8A2 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC32M16A2 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:512Mb x4, x8, x16 SDRAM |
發布緊急采購，3分鐘左右您將得到回復。