參數資料
型號： PIC16F1527T-I/PT
廠商： Microchip Technology
文件頁數： 52/94頁
文件大小： 0K
描述： MCU 28KB FLASH 1536B RAM 64-TQFP
標準包裝： 1,200
系列： PIC® XLP™ 16F
核心處理器： PIC
芯體尺寸： 8-位
速度： 20MHz
連通性： I²C，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 54
程序存儲器容量： 28KB（16K x 14）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 8
電壓 - 電源 (Vcc/Vdd)： 2.3 V ~ 5.5 V
數據轉換器： A/D 30x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 帶卷 (TR)
217
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
However, it is important that the TWINT bit is set in the value written. Writing a one to
TWINT clears the flag. The TWI will not start any operation as long as the TWINT bit in
TWCR is set. Immediately after the application has cleared TWINT, the TWI will initiate
transmission of the data packet.
6.
When the data packet has been transmitted, the TWINT Flag in TWCR is set, and TWSR
is updated with a status code indicating that the data packet has successfully been sent.
The status code will also reflect whether a Slave acknowledged the packet or not.
7.
The application software should now examine the value of TWSR, to make sure that the
data packet was successfully transmitted, and that the value of the ACK bit was as
expected. If TWSR indicates otherwise, the application software might take some special
action, like calling an error routine. Assuming that the status code is as expected, the
application must write a specific value to TWCR, instructing the TWI hardware to transmit
a STOP condition. Which value to write is described later on. However, it is important that
the TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI
will not start any operation as long as the TWINT bit in TWCR is set. Immediately after
the application has cleared TWINT, the TWI will initiate transmission of the STOP condi-
tion. Note that TWINT is NOT set after a STOP condition has been sent.
Even though this example is simple, it shows the principles involved in all TWI transmissions.
These can be summarized as follows:
When the TWI has finished an operation and expects application response, the TWINT Flag is
set. The SCL line is pulled low until TWINT is cleared.
When the TWINT Flag is set, the user must update all TWI Registers with the value relevant for
the next TWI bus cycle. As an example, TWDR must be loaded with the value to be transmitted
in the next bus cycle.
After all TWI Register updates and other pending application software tasks have been
completed, TWCR is written. When writing TWCR, the TWINT bit should be set. Writing a one
to TWINT clears the flag. The TWI will then commence executing whatever operation was
specified by the TWCR setting.
In the following an assembly and C implementation of the example is given. Note that the code
below assumes that several definitions have been made, for example by using include-files.
相關PDF資料
PDF描述
PIC16LF1527T-I/PT MCU PIC 28KB FLASH 64TQFP
7-227079-1 PLUG, COML BNC, KIT
V24A3V3C264BL3 CONVERTER MOD DC/DC 3.3V 264W
MIC2010-2PCQS IC USB PWR CTRLR DUAL 16-QSOP
PIC16LC58B-04/SO IC MCU OTP 2KX12 18SOIC
相關代理商/技術參數
參數描述
PIC16F1613-E/P 制造商:Microchip Technology Inc 功能描述:3.5KB Flash, 256 RAM, 32MHz Int. Osc, 10bit ADC, ZCD, WWDT, CRC, 14 PDIP .300in
PIC16F1613-I/SL 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube
PIC16F1613-I/ST 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Rail/Tube
PIC16F1613T-I/ML 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Tape and Reel
PIC16F1613T-I/SL 制造商:Microchip Technology Inc 功能描述:3.5KB FLASH, 256 RAM, 32MHZ INT. OSC, 10BIT ADC, ZCD, WWDT, - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*