- 您現在的位置：買賣IC網 > PDF目錄370013 > PowerNP NPe405L (IBM Microeletronics) 32-Bit Embedded Processor(32位嵌入式處理器) PDF資料下載
參數資料
| 型號： | PowerNP NPe405L |
| 廠商： | IBM Microeletronics |
| 英文描述： | 32-Bit Embedded Processor(32位嵌入式處理器) |
| 中文描述： | 32位嵌入式處理器（32位嵌入式處理器） |
| 文件頁數： | 27/48頁 |
| 文件大小： | 741K |
| 代理商： | POWERNP NPE405L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Advance Information
PowerNP
TM
NPe405L Embedded Processor Data Sheet
27
Signal List
The table following table provides a summary of the number of package pins associated with each functional
interface group.
In the table “Signal Functional Description” on page 28, each external signal is listed along with a short
description of the signal function. The signals are grouped together according to their function. Some signals
are multiplexed on the same package pin (ball) so that the pin can be used for different functions. In most
cases, the signal name is shown in this table without any multiplexed signal names that may be associated
with it. In cases where multiplexed signals are in the same functional group, the names appear as a default
signal followed by secondary signals in square brackets (for example, PCIC0:3[BE0:3]). Active-low signals
such as BE0:3 are marked with an overline. Any signal that is not the primary (default) signal on a multiplexed
pin is shown in square backets.
The active signal on a multiplexed pin is controlled by programming. It is expected that in any single
application, a particular pin will always be programmed to serve the same function. The flexibility of
multiplexing allows a single chip to offer a richer pin selection than would otherwise be possible.
In addition to multiplexing, many pins are also multi-purpose. For example, EMC0TxErr[EMC0Tx1En]
functions as an error output when the Ethernet interface operates in MII mode, or as a transmit enable output
when operating in RMII mode.
One group of pins is used as strapped inputs during system reset. These pins function as strapped inputs
only during reset and are used for other functions during normal operation (see “Initialization” on page 47).
Note that these are
not multiplexed
pins since the function of the pins is not programmable.
The following table lists all of the I/O signals provided by the NPe405L. Please refer to “Signals Listed
Alphabetically” on page 13 for the pin number to which each signal is assigned.
Pin Summary
Group
No. of Pins
Nonmultiplexed Signals
167
Multiplexed Signals
48
Total Signal Pins
215
AV
DD
OV
DD
V
DD
Gnd
1
16
8
48
Thermal (and Gnd)
36
Reserved
0
Total Pins
324
相關PDF資料 |
PDF描述 |
|---|---|
| PowerNP NPe405 | 32-Bit Embedded Processor(32位嵌入式處理器（應用于網絡方面，提供高性價比）) |
| PowerPC 401GF | 32-bit RISC Embedded Controllers(32位RISC結構嵌入式控制器) |
| PowerPC 403GA | 32-bit RISC Embedded Controllers(32位RISC結構嵌入式控制器) |
| PowerPC 403GB | 32-bit RISC Embedded Controllers(32位RISC結構嵌入式控制器) |
| PowerPC 403GC | 32-bit RISC Embedded Controllers(32位RISC結構嵌入式控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| POWERPAC-B | 制造商:IAR Systems 功能描述:PowerPac |
| POWERPAC-S | 制造商:IAR Systems 功能描述:PowerPac |
| POWERPAT PLUS | 制造商:Fluke Electronics 功能描述:SOFTWARE PAT |
| POWERPATPLUS | 制造商:Fluke Electronics 功能描述:Fluke Powerpat Plus |
| POWERPLUG15W | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AC/DC POWER SUPPLY |
發布緊急采購，3分鐘左右您將得到回復。