- 您現在的位置：買賣IC網 > PDF目錄373259 > REFERENCEMANUAL Reference Manual - ElanSC400 Register Set Reference Manual (Including Changes for the 蒷anSC410 Microcontroller) PDF資料下載
參數資料
| 型號： | REFERENCEMANUAL |
| 英文描述： | Reference Manual - ElanSC400 Register Set Reference Manual (Including Changes for the 蒷anSC410 Microcontroller) |
| 中文描述： | 參考手冊- ElanSC400寄存器組參考手冊（包括微控制器的蒷anSC410變化） |
| 文件頁數： | 6/40頁 |
| 文件大小： | 405K |
| 代理商： | REFERENCEMANUAL |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
6
élanSC400 Microcontroller Register Set Reference Manual Amendment
A M E N D M E N T
2-144 COM1 Baud Clock
Divisor Latch LSB,
Address 03F8h; default
bit values in diagram
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 1
Divisor must be
nonzero
COM1 Baud Clock
Divisor Latch LSB,
Address 03F8h;
Programming Notes
Programming Notes
Programming Notes
In order to determine the UART baud
rate that will result from a particular
setting of the baud rate divisor latch,
the 16x baud clock is divided by 16 to
give a normalized baud rate. Because
the standard 16x baud clock runs at
1.8432 MHz, the “normalized” baud
rate is 115200. This rate is then
divided by the value of the 16-bit baud
clock divisor latch register. It is invalid
to program a baud rate divisor of 0.
The baud rate divisor latch, being a
16-bit value, provides for up to 64k–1
different baud rates (0 is not a valid
baud rate). However, only a few of the
available rates are ever used in
common practice. See the following
table for the commonly used baud
rates along with the baud rate divisor
required to achieve them:
Baud
Divisor Latch Value
110
150
300
600
1200
2400
4800
9600
19200
38400
57600
115200
0417h
0300h
0180h
00C0h
0060h
0030h
0018h
000Ch
0006h
0003h
0002h
0001h
Add text to
programming
notes on both
pages.
2-145 COM1 Baud Clock
Divisor Latch MSB,
Address 03F9h;
Programming Notes
2-147 COM1 Interrupt ID
Register, Address
03FAh; default value
for bit 0 in diagram
0 0 = No significance
0 1 = No significance
1 0 = 16450-compatible mode is
enabled
1 1 = 16550-compatible mode is
enabled
0 0 = 16450-Compatible mode is
enabled (default)
0 1 = No significance
1 0 = No significance
1 1 = 16550-Compatible mode is
enabled
Default of 0 0
indicates 16450-
Compatible
mode.
2-150 COM1 Modem Control
Register, Address
03FCh; bit 3
description
Enable COM2 Interrupts
Enable COM1 Interrupts
Correction.
2-153 COM1 Modem Status
Register, Address
03FEh; default bit
values in diagram
x x x x 0 0 0 0
0 0 0 0
“” = depends
on input state.
Table 1.
Corrections to the
élanSC400 Microcontroller Register Set Reference Manual
(Continued)
Page Item
Original Text
Change To
Comment
相關PDF資料 |
PDF描述 |
|---|---|
| REG103-25 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-27 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-3 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-33 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-5 | DMOS 500mA Low Dropout (LDO) Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| REF-H100 | 制造商:PEPPERL+FUCHS 功能描述:PHOTO ACCESSORY - REFLECTOR |
| REF-H100-2R | 制造商:PEPPERL+FUCHS 功能描述:Photoelectric (Automation) |
| REF-H180 | 制造商:PEPPERL+FUCHS 功能描述:Reflector, Photoelectric, Rectangular, 180mm x 40mm x 7.4mm, 2 Mounting Holes |
| REF-H23 | 制造商:PEPPERL+FUCHS 功能描述:Reflector, rectangular, 14 mm x 19 mm |
| REF-H32 | 制造商:PEPPERL+FUCHS 功能描述:Reflector, Hexagonal, 55mm x 25mm Size, w/Mounting Holes 制造商:PEPPERL+FUCHS 功能描述:SENSOR REFLECTOR 制造商:PEPPERL+FUCHS 功能描述:SENSOR REFLECTOR; Reflector Type:Corner Cube; Accessory Type:Reflector; For Use With:All Photoelectric Sensors; Size:2.2 x 1 x 0.37 in; Temperature Max:65C; Type:Side Mounting Holes ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。