參數資料
型號: RG82845MP
英文描述: Controller Miscellaneous - Datasheet Reference
中文描述: 控制器雜項-數據表參考
文件頁數: 117/157頁
文件大?。?/td> 1407K
代理商: RG82845MP
Intel
82845MP/82845MZ Chipset-Mobile (MCH-M)
62
Datasheet
250687-002
R
Bit
Description
6:4
Mode Select (SMS). These bits select the special operational mode of the DRAM interface. The
special modes are intended for initialization at power up.
000: Post Reset state – When the MCH-M exits reset (power-up or otherwise), the mode select field
is cleared to “000”.
During any reset sequence, while power is applied and reset is active, the MCH-M asserts all CKE
signals. After internal reset is de-asserted, CKE signals remain de-asserted until this field is written to
a value different than “000”. On this event, all CKE signals are asserted.
During suspend, MCH-M internal signal triggers DRAM controller to flush pending commands and
enter all rows into Self-Refresh mode. As part of resume sequence, MCH-M will be reset – which will
clear this bit field to “000” and maintain CKE signals de-asserted. After internal reset is de-asserted,
CKE signals remain de-asserted until this field is written to a value different than “000”. On this event,
all CKE signals are asserted.
During entry to other low power states (C3, S1M), MCH-M internal signal triggers DRAM controller to
flush pending commands and enter all rows into Self-Refresh mode. During exit to normal mode,
MCH-M signal triggers DRAM controller to exit Self-Refresh and resume normal operation without
S/W involvement.
001: NOP Command Enable – All CPU cycles to DRAM result in a NOP command on the DRAM
interface.
010: All Banks Pre-charge Enable – All CPU cycles to DRAM result in an “all banks precharge”
command on the DRAM interface.
011: Mode Register Set Enable – All CPU cycles to DRAM result in a “mode register” set command
on the DRAM interface. Host address lines are mapped to memory address lines in order to specify
the command sent. Host address lines [15:3] are mapped to MA[12:0].
100: Extended Mode Register Set Enable – All processor cycles to SDRAM result in an “extended
mode register set” command on the DRAM interface (DDR only). Host address lines are mapped to
DDR address lines in order to specify the command sent. Host address lines [15:3] are mapped to
MA[12:0].
101: Reserved
110: CBR Refresh Enable – In this mode all CPU cycles to DRAM result in a CBR cycle on the DDR
interface
111: Normal operation
3:0
Reserved
相關PDF資料
PDF描述
RG82845MZ Controller Miscellaneous - Datasheet Reference
RG82870P2 Controller Miscellaneous - Datasheet Reference
RH5RE36AA-T1-FA 3.6 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PSSO3
RH5RE56AA-T1-FA 5.6 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PSSO3
RE5RE36AA-TZ-FC 3.6 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PBCY3
相關代理商/技術參數
參數描述
RG82845MP S L66J 制造商:Intel 功能描述:Chipset Memory Controller Hub Mobile 593-Pin FCBGA
RG82845MZ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference
RG82845PE S L6H5 制造商:Intel 功能描述:CHIPSTGMCH 82845PE HT-PBGA760
RG82845PESL6Q3 制造商:Intel 功能描述:Chipsets
RG82845-SL5V7 制造商:Intel 功能描述:INTEL 845G GRAPHICS AND MEMORY CONTROLLER HUB(GMCH)