參數資料
型號： S29PL032J70BAW13
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 70 ns, PBGA56
封裝： 7 X 9 MM, FBGA-56
文件頁數： 67/100頁
文件大小： 967K
代理商： S29PL032J70BAW13
March 15, 2004 31107A5
S29PL127J/S29PL129J/S29PL064J/S29PL032J
69
PR EL IMINAR Y
operation using the DQ7 or DQ6 status bits, just as in the standard Word Program
operation. Refer to the "Write Operation Status" section section for more
information.
In the erase-suspend-read mode, the system can also issue the autoselect com-
mand sequence. The device allows reading autoselect codes even at addresses
within erasing sectors, since the codes are not stored in the memory array. When
the device exits the autoselect mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation. Refer to the "SecSiTM Sector Ad-
details.
To resume the sector erase operation, the system must write the Erase Resume
command (address bits are don’t care). The bank address of the erase-sus-
pended bank is required when writing this command. Further writes of the
Resume command are ignored. Another Erase Suspend command can be written
after the chip has resumed erasing.
If the Persistent Sector Protection Mode Locking Bit is verified as programmed
without margin, the Persistent Sector Protection Mode Locking Bit Program Com-
mand should be reissued to improve program margin. If the SecSi Sector
Protection Bit is verified as programmed without margin, the SecSi Sector Pro-
tection Bit Program Command should be reissued to improve program margin.
After programming a PPB, two additional cycles are needed to determine
whether the PPB has been programmed with margin. If the PPB has been pro-
grammed without margin, the program command should be reissued to improve
the program margin. Also note that the total number of PPB program/erase cycles
is limited to 100 cycles. Cycling the PPBs beyond 100 cycles is not guaranteed.
After erasing the PPBs, two additional cycles are needed to determine whether
the PPB has been erased with margin. If the PPBs has been erased without mar-
gin, the erase command should be reissued to improve the program margin. The
programming of either the PPB or DYB for a given sector or sector group can be
verified by writing a Sector Protection Status command to the device.
Note that there is no single command to independently verify the programming
of a DYB for a given sector group.
相關PDF資料
PDF描述
S29WS128J0PBFW002 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84
S29WS128J0PBAW002 8M X 16 FLASH 1.8V PROM, 55 ns, PBGA84
S2M 2 A, 1000 V, SILICON, RECTIFIER DIODE, DO-214AA
S2R72A44F12C4 UNIVERSAL SERIAL BUS CONTROLLER, PQFP48
S2V20-4000 1.7 A, 200 V, SILICON, RECTIFIER DIODE
相關代理商/技術參數
參數描述
S29PL032J70BFI120 功能描述:閃存 32Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BFI120(E) 制造商:Spansion 功能描述:Cut Tape
S29PL032J70BFI122 功能描述:閃存 32Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL032J70BFI123 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29PL064J 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*