- 您現在的位置：買賣IC網 > PDF目錄16215 > SI3232PPT0-EVB (Silicon Laboratories Inc)BOARD EVAL W/SI3200 INTERFACE PDF資料下載
參數資料
| 型號： | SI3232PPT0-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 51/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL W/SI3200 INTERFACE |
| 標準包裝： | 1 |
| 系列： | ProSLIC® |
| 主要目的： | 接口，模擬前端（AFE） |
| 已用 IC / 零件： | Si3232 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Si3232
Preliminary Rev. 0.96
29
Not
Recommended
fo
r N
ew
D
esi
gn
s
4.5. Automatic Dual Battery Switching
The Si3232 and Si3200 provide the ability to switch
between several user-provided battery supplies to aid
thermal management. This method is required during
the ringing to off-hook and on-hook to off-hook state
transitions.
During the on-hook operating state, the Si3232 must
operate from the ringing battery supply in order to
quickly
provide
the
desired
ringing
signal
when
required.
Once
an
off-hook
condition
has
been
detected, the Si3232 must transition to the lower battery
supply (typically –24 V, in order to reduce power
dissipation during the active state). The low current
consumed by the Si3232 during the on-hook state
results in very little power dissipation while being
powered from the ringing battery supply, which can
have an amplitude as high as 100 V depending on the
desired ringing amplitude.
The BATSEL pins serve to switch between the two
battery voltages based on the operating state and the
TIP-RING
voltage.
illustrates
the
chip
connections required to implement an automatic dual
battery switching scheme. When BATSEL is pulled low,
the desired channel is powered from the VBLO supply.
When BATSEL is pulled high, the VBHI source will
supply power to the desired channel.
The BATSEL pins for both channels are controlled using
the BATSEL bit of the RLYCON register and should be
programmed to automatically switch to the lower battery
supply (VBLO) whenever an off-hook condition is
sensed.
Two thresholds are provided to enable battery switching
with hysteresis. The BATHTH RAM location specifies
the threshold at which the Si3232 will switch from the
low battery, VBLO, to the high battery, VBHI, due to an
off-hook to on-hook transition. The BATLTH RAM
location specifies the threshold at which the Si3232 will
switch from VBHI to VBLO due to a transition from the on-
hook or ringing state to the off-hook state or because
the overhead during active off-hook mode is sufficient to
feed the subscriber loop using a lower battery voltage.
The low-pass filter coefficient is calculated using the
equation below and is entered into the BATLPF RAM
location.
BATLPF = [(2
f x 4096)/800] x 23
Where f = the desired cutoff frequency of the filter
The programmable range of the filter is from 0 (blocks
all signals) to 4000h (unfiltered). A typical value of 10
(0A10h) is sufficient to filter out any unwanted ac
artifacts while allowing the dc information to pass
through the filter.
Table 17 provides the register and RAM locations used
for programming the battery switching functions.
Table 17. Register and RAM Locations used for Battery Switching
Parameter
Register/RAM
Mnemonic
Register/RAM
Bits
Programmable
Range
Resolution
(LSB Size)
High Battery Detect Threshold
BATHTH
BATHTH[14:0]
0 to 160.173 V*
628 mV
(4.907 mV)
Low Battery Detect Threshold
BATLTH
BATLTH[14:0]
0 to 160.173 V*
628 mV
(4.907 mV)
Ringing Battery Switch
RLYCON
GPO
Toggle
N/A
Battery Select Indicator
RLYCON
BSEL
Toggle
N/A
Battery Switching LPF
BATLPF
BATLPF[15:3]
0 to 4000
N/A
*Note: The usable range for BATHTH and BATLTH is limited to the
VBHI voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| UPZW6101MHD | CAP ALUM 100UF 420V 20% RADIAL |
| SI3232DC0-EVB | DAUGHTER CARD W/SI3200 INTERFACE |
| UPZ2D391MHD | CAP ALUM 390UF 200V 20% RADIAL |
| SI3230PPQX-EVB | BOARD EVAL W/DISCRETE INTERFACE |
| M3UFK-1636R | IDC CABLE - MKS16K/MC16M/MCF16K |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3232PPTX-EVB | 功能描述:音頻 IC 開發工具 Si3232 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| SI3232-X-FQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DUAL PROGRAMMABLE CMOS SLIC WITH LINE MONITORING |
| SI3232-X-GQ | 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROGRAMMABLE CMOS SLIC WITH LINE MONITORING |
| SI3233 | 制造商:SILABS 制造商全稱:SILABS 功能描述:PROSLIC㈢ PROGRAMMABLE CMOS SLIC WITH RINGING/BATTERY VOLTAGE GENERATION |
| Si3233-C-FM | 功能描述:射頻無線雜項 Single-Chan SLIC RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。