參數資料
型號: SMARTPSE24-KIT
廠商: Silicon Laboratories Inc
文件頁數: 10/36頁
文件大小: 0K
描述: KIT EVAL REF 24PORT SPI/UART
標準包裝: 1
主要目的: 電源管理,以太網供電(POE),PSE
已用 IC / 零件: Si3452,Si3482,Si3500
已供物品: 板,線纜,CD
相關產品: SI3482-A01-GM-ND - IC CTLR POE 24-48PORT PSE 24-QFN
336-1830-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1835-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1829-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1831-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1834-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1844-5-ND - IC POE SWITCH PWR OVER LAN 20QFN
336-1833-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
336-1832-5-ND - IC POE CONTROLLER MIDSPAN 40QFN
Si3452
18
Rev. 1.3
5.4. Port Configuration (Registers 0x0A–0x11)
These registers indicate the port configuration and are read/write registers.
The port priority bit is set if the port is not high priority. Low-priority ports are shut down when the shutdown low-
priority ports command is issued.
The “PoE+” bit specifies the dc current limit at either 425 mA or 850 mA nominal*.
*Note:
The PoE+ mode should be set correctly according to the electrical design of the PSE circuit (transformer and conductor
current carrying capacity). The PoE+ port mode can safely be changed prior to port turn-on, but changes after port turn-
on do not have an immediate effect and are not recommended.
“Disconnect enable” must be set for power to be removed if there is a disconnect. “Port mode” is set according to
ICUT is the nominal current level at which the port will automatically power down if ICUT is exceeded for 60 ms. It
can be set with 3.2 mA resolution. The accuracy of current measurement is approximately 5%; so, ICUT is normally
set 7% higher than the supported current level. ICUT is automatically set based on the classification result and
PoE+ mode. The automatically-set ICUT level is appropriate for a 45 V minimum system power supply for classes
0–3 and for a 51 V minimum power supply for PoE+ mode. This feature is classification policing.
If the Si3452 is in the semi-auto mode, ICUT will not be updated according to the classification result. This means
that if it is desired to set ICUT at port turn-on, this should be done before the port is turned on.
Once a port is turned on, ICUT can be changed dynamically. It is often undesirable to use a low value of ICUT during
port turn-on because inrush can trigger the ICUT event. For this reason, it is normal to allow the port to turn on with
the automatic ICUT setting and then later change this value after port current has stabilized and also if the PD and
PSE have negotiated for a different ICUT value based on the PoE L2 power negotiation protocol (LLDP).
The Si3452 supports 2-Event classification as defined in the IEEE 802.3at draft. 2-event classification is an
alternative to L2 power management where the PSE advertises it is capable of PoE powering by generating two
classification pulses. 2-Event classification is only supported for auto mode. If the Si3452 is in auto mode and the
first event classification result is Class 4, the mark, second event, and second mark are performed. Power is
applied only if the second event is also Class 4. If the second event is not Class 4, the classification error is
reported, and the port will not power. If the port is in manual mode, classification is done prior to turning on the port.
Table 17. Port Mode Selection
Port Mode Setting
B1, B0
Mode
Description
00b
Shutdown
The power is shut down with no detection pulses.
A command to manually power the port is ignored.
01b
Manual
The port can be powered by the manual power command.
10b
Semiauto
Detection is done and classification is done for Rgood, but the port does
not power.
11b
Auto
Detection classification and port powering are all automatic with no host
intervention required. ICUT and ILIM are automatically set according to
the PoE+ mode and classification result.
相關PDF資料
PDF描述
LBC2518T681M INDUCTOR WOUND 680UH 45MA 1007
VE-24D-EX CONVERTER MOD DC/DC 85V 75W
1SMA5926BT3 DIODE ZENER 11V 1.5W SMA
ST16C2550CQ-0B-EB EVAL BOARD FOR ST16C2551 48TQFP
9-6278032-5 C/A MT-RJ/MT-RJ MM
相關代理商/技術參數
參數描述
SMARTRF06EBK 功能描述:射頻開發工具 SMARTRF06 EVAL BRD RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
SMARTRFTRXEBK 功能描述:EVAL BOARD SMART RF 制造商:texas instruments 系列:- 零件狀態:有效 類型:收發器 頻率:- 配套使用產品/相關產品:MSP430 所含物品:板,線纜 標準包裝:1
SMARTSOCKET 575 TYPE D 制造商:TIME MARK CORP SIGNALINE 功能描述:Nominal input voltage 575VAC, Max input voltage 635VAC
SMARTSTART-BAC-D 制造商:IDEC Corporation 功能描述:PROGRAMMABLE LOGIC CONTROLLER, Accessory Type:Starter Kit, For Use With:FL1D Ser
SMARTSTART-BAC-E 制造商:IDEC Corporation 功能描述:FL1E SMARTRELAY STARTER KIT 120-240VAC/DC BASE MODULE W/O LCD DISPLAY 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTRO 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTROL; No. of Inputs:12; No. of Outputs:12; Kit Contents:WindLGC 6.0 Software, FL1E-B12RCC and Serial Programming Cable; Supply Voltage Max:240VAC; Accessory Type:SmartRelay Starter Kit 制造商:IDEC Corporation 功能描述:FL1E-B12RCC, Windlgc Software And Programming Cable 制造商:IDEC CORPORATION 功能描述:FL1E SmartRelay Starter Kit