REV. 5.0.3 2.2 5-Volt Tolerant Inputs The 650A can acccept up to 5V inputs even" />
參數資料
型號： ST16C650ACQ48-F
廠商： Exar Corporation
文件頁數： 2/50頁
文件大?。?/td> 0K
描述： IC UART FIFO 32B 48TQFP
標準包裝： 250
特點： *
通道數： 1，UART
FIFO's： 32 字節
規程： 打印機，RS232，RS422，RS485
電源電壓： 2.9 V ~ 5.5 V
帶并行端口： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
其它名稱： 1016-1662
ST16C650ACQ48-F-ND
ST16C650A
10
2.90V TO 5.5V UART WITH 32-BYTE FIFO
REV. 5.0.3
2.2
5-Volt Tolerant Inputs
The 650A can acccept up to 5V inputs even when operating at 3.3V. Caution: XTAL1 is not 5 volt tolerant.
2.3
Device Reset
The RESET input resets the internal registers and the serial interface outputs to their default state (see
Figure 13). An active high pulse of longer than 40 ns duration will be required to activate the reset function in
the device.
2.4
Device Identification and Revision
The ST16C650A provides a Device Identification code and a Device Revision code to distinguish the part from
other devices and revisions. To read the identification code from the part, it is required to set the baud rate
generator registers DLL and DLM both to 0x00. Now reading the content of the DLM will provide 0x04 for the
ST16C650A and reading the content of DLL will provide the revision of the part; for example, a reading of 0x01
means revision A.
2.5
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# and TXRDY# output pins. The transmit and receive FIFO trigger levels provide additional
flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the transmitter is
empty or has an empty location(s) for more data. The user can optionally operate the transmit and receive
FIFO in the DMA mode (FCR bit-3=1). When the transmit and receive FIFO are enabled and the DMA mode is
disabled (FCR bit-3 = 0), the 650A is placed in single-character mode for data transmit or receive operation.
When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode operation by loading or
unloading the FIFO in a block sequence determined by the programmed trigger level. In this mode, the 650A
sets the TXRDY# pin when the transmit FIFO becomes full, and sets the RXRDY# pin when the receive FIFO
becomes empty. The following table shows their behavior. Also see Figures 23 through 28.
TABLE 2: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR BIT-3 = 0
(DMA MODE DISABLED)
FCR BIT-3 = 1
(DMA MODE ENABLED)
RXRDY#
0 = 1 byte.
1 = no data.
0 = at least 1 byte in FIFO
1 = FIFO empty.
1 to 0 transition when FIFO reaches the trigger
level, or timeout occurs.
0 to 1 transition when FIFO empties.
TXRDY#
0 = THR empty.
1 = byte in THR.
0 = FIFO empty.
1 = at least 1 byte in FIFO.
0 = FIFO has at least 1 empty location.
1 = FIFO is full.
相關PDF資料
PDF描述
XR68M752IM48-F IC UART FIFO 64B DUAL 48TQFP
XR16M752IM48-F IC UART FIFO 34B DUAL 48TQFP
ST16C450CQ48-F IC UART SINGLE 48TQFP
ST16C2450IQ48-F IC UART FIFO DUAL 48TQFP
MAX7314AEG+T IC I/O EXPANDER I2C 16B 24QSOP
相關代理商/技術參數
參數描述
ST16C650ACQ48TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C650ACQ48TR-F
ST16C650AIJ44 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650AIJ44-F 功能描述:UART 接口集成電路 UART W/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C650AIP40 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650AIQ48 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:UART, 48 Pin, Plastic, TQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*