- 您現在的位置：買賣IC網 > PDF目錄385870 > ST6228CN3 (意法半導體) CB 5C 5#16S PIN RECP WALL PDF資料下載
參數資料
| 型號： | ST6228CN3 |
| 廠商： | 意法半導體 |
| 英文描述： | CB 5C 5#16S PIN RECP WALL |
| 中文描述： | 8位單片機與微控制器/ D轉換器，自動重加載定時器，UART的秘書長辦公室，安全復位和28引腳封裝 |
| 文件頁數： | 19/84頁 |
| 文件大小： | 561K |
| 代理商： | ST6228CN3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
19/84
19
ST62T28C/E28C
3.2 RESETS
The MCU can be reset in four ways:
– by the external Reset input being pulled low;
– by Power-on Reset;
– by the digital Watchdog peripheral timing out.
– by Low Voltage Detection (LVD)
3.2.1 RESET Input
The RESET pin may be connected to a device of
the application board in order to reset the MCU if
required. The RESET pin may be pulled low in
RUN, WAIT or STOP mode. This input can be
used to reset the MCU internal state and ensure a
correct start-up procedure. The pin is active low
and features a Schmitt trigger input. The internal
Reset signal is generated by adding a delay to the
external signal. Therefore even short pulses on
the RESET pin are acceptable, provided V
DD
has
completed its risingphase and that the oscillatoris
running correctly (normal RUN or WAIT modes).
The MCU is kept in the Reset state as long as the
RESET pin is held low.
If RESET activation occurs in the RUN or WAIT
modes, processing of the user program is stopped
(RUN modeonly), the Inputs and Outputs are con-
figured as inputs with pull-up resistors and the
main Oscillator is restarted. When the level on the
RESET pin then goes high, the initialization se-
quence is executed following expiry of the internal
delay period.
If RESET pin activation occurs in the STOP mode,
the oscillator starts up and all Inputs and Outputs
are configured as inputs with pull-up resistors.
When the level of the RESET pin then goes high,
the initialization sequence is executed following
expiry of the internal delay period.
3.2.2 Power-on Reset
The function of the POR circuit consists in waking
up the MCU by detecting around 2V a dynamic
(rising edge) variation of the VDD Supply. At the
beginning of this sequence, the MCU is configured
in the Reset state: all I/O ports are configured as
inputs with pull-up resistors and no instruction is
executed. When the power supply voltage rises to
a sufficient level, the oscillator starts to operate,
whereupon aninternal delay is initiated, in order to
allow the oscillator to fully stabilize before execut-
ing the first instruction. The initialization sequence
is executed immediately following the internal de-
lay.
To ensure correct start-up, the user should take
care that the VDD Supply is stabilized at a suffi-
cient level for the chosen frequency (see recom-
mended operation) before the reset signal is re-
leased. In addition, supply rising must start from
0V.
As a consequence, the POR does not allow to su-
pervise static, slowly rising, or falling, or noisy
(presenting oscillation) VDD supplies.
An external RC network connected to the RESET
pin, or the LVD reset can be used instead to get
the best performances.
Figure 13. Reset and Interrupt Processing
INNMI MASK SET
( IF PRESENT )
RESET
SELECT
NMI MODE FLAGS
IS RESET STILL
PRESENT
YES
PUT FFEH
ON ADDRESS BUS
FROM RESET LOCATIONS
FFE/FFF
NO
FETCH INSTRUCTION
LOAD PC
VA000427
相關PDF資料 |
PDF描述 |
|---|---|
| ST6228CN6 | ER 5C 5#16S PIN RECP WALL |
| ST6391 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6392B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6393B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6395B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST6228CN3/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST6228CN6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 28-PIN PACKAGE |
| ST6228CN6/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST622X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8/16-Bit Micros |
| ST622XC-KIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STARTER KIT DATASHEET FOR ST620X. ST621X AND ST622X |
發布緊急采購，3分鐘左右您將得到回復。