- 您現在的位置：買賣IC網 > PDF目錄385870 > ST6228CN3 (意法半導體) CB 5C 5#16S PIN RECP WALL PDF資料下載
參數資料
| 型號： | ST6228CN3 |
| 廠商： | 意法半導體 |
| 英文描述： | CB 5C 5#16S PIN RECP WALL |
| 中文描述： | 8位單片機與微控制器/ D轉換器，自動重加載定時器，UART的秘書長辦公室，安全復位和28引腳封裝 |
| 文件頁數： | 35/84頁 |
| 文件大?。?/td> | 561K |
| 代理商： | ST6228CN3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
35/84
35
ST62T28C/E28C
I/O PORTS
(Cont’d)
4.1.1 Operating Modes
Each pinmay be individually programmed asinput
or output with various configurations.
This is achieved by writing the relevant bit in the
Data (DR), Data Direction (DDR) and Option reg-
isters (OR). Table 12 illustrates the various port
configurations which can be selected by user soft-
ware.
4.1.1.1 Input Options
Pull-up, High Impedance Option. All input lines
can be individually programmed with or withoutan
internal pull-up by programming the OR and DR
registers accordingly. If the pull-up option is not
selected, the input pin will be in the high-imped-
ance state.
4.1.1.2 Interrupt Options
All input lines can be individually connected by
software to the interrupt system by programming
the OR and DR registers accordingly. The inter-
rupt trigger modes (falling edge, rising edge and
low level) can be configured by software as de-
scribed in the Interrupt Chapter for each port.
4.1.1.3 Analog Input Options
Some pins can be configured as analog inputs by
programming the OR and DR registers according-
ly. These analog inputs are connected to the on-
chip 8-bit Analog to Digital Converter. ONLY ONE
pin should be programmed as an analog input at
any time, since by selecting more than one input
simultaneously their pins will be effectively short-
ed.
Table 12. I/O Port Option Selection
Note:
X = Don’t care
DDR
0
0
0
0
1
1
OR
0
0
1
1
0
1
DR
0
1
0
1
X
X
Mode
Input
Input
Input
Input
Output
Output
Option
With pull-up, no interrupt
No pull-up, no interrupt
With pull-up and with interrupt
Analog input (when available)
Open-drain output (20mA sink when available)
Push-pull output (20mA sink when available)
相關PDF資料 |
PDF描述 |
|---|---|
| ST6228CN6 | ER 5C 5#16S PIN RECP WALL |
| ST6391 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6392B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6393B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6395B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST6228CN3/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST6228CN6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 28-PIN PACKAGE |
| ST6228CN6/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST622X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8/16-Bit Micros |
| ST622XC-KIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STARTER KIT DATASHEET FOR ST620X. ST621X AND ST622X |
發布緊急采購，3分鐘左右您將得到回復。