- 您現在的位置：買賣IC網 > PDF目錄372405 > SZA1000H (NXP SEMICONDUCTORS) QIC digital equalizer PDF資料下載
參數資料
| 型號： | SZA1000H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | QIC digital equalizer |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 164K |
| 代理商： | SZA1000H |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
1998 Feb 16
7
Philips Semiconductors
Product specification
QIC digital equalizer
SZA1000
Stripe detector
This circuit is used to signal the stripes in QIC 3080,
QIC 3095 and TR4 servo formats (STRIPE output on
pin 21 must be selected; see Table 22). A frequency
detector counts the peaks above the qualification
threshold (see Table 29). An input signal containing
frequencies within
±
25% of the programmable nominal
frequency will be detected as a stripe. The microcontroller
can then poll the amplitude of the following burst via the
serial interface.
Differentiator
This function is realized by subtracting samples. The delay
between samples is programmable between 1 and 6
periods of f
s
, split into two parts to provide a balanced
delay between the differentiated and non-differentiated
signals (see Tables 24 to 26).
The PLL
This is a fully digital PLL (Phase Lock Loop) with a
programmable nominal frequency (see Tables 35 and 36),
zero phase restart, programmable window shift
(WIN_SHIFT; control register address 42) and a loop filter
with two separate programmable settings.
The PLL output reference clock is the RRC signal (pin 25;
see Table 34). The frequency of this signal is rounded in
time to f
s
. The PLL is switched to the nominal frequency if
RG (pin 20) is LOW, and makes a zero phase restart at the
first detected peak after RG goes HIGH.
The LTD input (pin 19) is used to select between the two
loop filter settings (see Tables 37 to 42). This allows for
fast lock-in during preamble, before switching to a lower
loop bandwidth for maximum data reliability (see Fig.3).
Fig.3 PLL timing diagram.
handbook, halfpage
SIGNALS
MGG583
RG
PLL
MODE
preamble
data
nominal
frequency
fast lock-in
normal read mode
zero phase restart
LTD
The maximum likelihood detector
This detector calculates the most likely position of the
peaks in the signal. It checks for (d,k) code constraints,
and for alternating peaks. If an error is detected, the ‘most
likely’ correction is implemented.
Separate corrections can be enabled or disabled.
The SRD output of the maximum likelihood detector is
valid during the rising edge of the RRC signal (see Fig.4).
The maximum likelihood detector is used only to generate
the SRD signal, and not to generate the time continuous
RD pulse.
The DAC
This is an internal differential 8-bit DAC operating at f
s
.
The LPF after the DAC
This analog LPF filters the time quantized signal from the
DAC to retain a time continuous signal. This provides more
accurate timing of the detected zero crossings in the RD
pulse output.
The LPF is a second order active filter with a cut-off
frequency of 8 MHz.
The read pulse circuit
A peak in the equalized signal at the interpolator output
generates a read pulse. The peak is detected if a zero
crossing occurs in the filtered signal after the DAC while
the non-differentiated signal is above the qualification
threshold.
Uncommitted current sources
Two uncommitted 5-bit programmable current sink DACs
(0 to 2 mA) are available as IO1 and IO2 (see Table 20 for
programming). These could be used, for example, to drive
the tape hole detector circuit.
Fig.4 SRD/RRC timing.
handbook, halfpage
MGG584
RRC
相關PDF資料 |
PDF描述 |
|---|---|
| SZF2002 | Low voltage 8-bit microcontroller with 6-kbyte embedded RAM(帶6K字節嵌入RAM的低壓8位微控制器) |
| SZF2002HL | Low voltage 8-bit microcontroller with 6-kbyte embedded RAM |
| T1012D | STANDARD TRIACS |
| T1012DH | STANDARD TRIACS |
| T1012M | STANDARD TRIACS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SZA1010 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Servo Driver 3 DSD-3 |
| SZA1010T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Servo Driver 3 DSD-3 |
| SZA1015TT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MOTOR CONTROLLER |
| SZ-A11 | 制造商:Fuji Electric 功能描述: |
| SZ-A11/T | 制造商:Fuji Electric 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。