參數資料
型號： TLV320AIC21I
廠商： Texas Instruments, Inc.
英文描述： Layout and Grounding Guidelines for TLV320AIC2x
中文描述： 為TLV320AIC2x布局和接地指南
文件頁數： 18/46頁
文件大?。?/td> 452K
代理商： TLV320AIC21I
SLAS428 AUGUST 2004
www.ti.com
18
and implement a shelving filter with 0 dB gain from dc to approximately 150 Hz, at which point it rolls off to a 3-dB attenuation
for higher frequency signals, thus giving a 3-dB boost to signals below 150 Hz. The N and D coefficients are represented
by 16-bit twos complement numbers with values ranging from –32768 to +32767. Frequency response plots are given in
the
Audio DAC Filter Frequency Responses
section of this data sheet.
Interpolation Filter
The interpolation filter upsamples the output of the digital audio processing block by the required oversampling ratio. It
provides a linear phase output with a group delay of 21/Fs.
In addition, a digital interpolation filter provides enhanced image filtering and reduces signal images caused by the
upsampling process that are below 20 kHz. For example, upsampling an 8-kHz signal produces signal images at multiples
of 8 kHz (i.e., 8 kHz, 16 kHz, 24 kHz, etc). The images at 8 kHz and 16 kHz are below 20 kHz and still audible to the listener;
therefore, they must be filtered heavily to maintain good output quality. The interpolation filter is designed to maintain at
least 65-dB rejection of images that land below 7.455 Fs. In order to utilize the programmable interpolation capability, the
Fsref should be programmed to a higher rate (restricted to be in the range of 39 kHz to 53 kHz when the PLL is in use),
and the actual Fs is set using the dividers in bit D5D3/REG00H/Page2. For example, if Fs = 8 kHz is required, then Fsref
can be set to 48 kHz, and the DAC Fs set to Fsref/6. This ensures that all images of the 8-kHz data are sufficiently attenuated
well beyond the ~20-kHz audible frequency range.
Delta-Sigma DAC
The audio digital-to-analog converter incorporates a third order multibit delta-sigma modulator followed by an analog
reconstruction filter. The DAC provides high-resolution, low-noise performance, using oversampling and noise shaping
techniques. The analog reconstruction filter design consists of a 6 tap analog FIR filter followed by a continuous time RC
filter. The analog FIR operates at a rate of 128 x Fsref (6.144 MHz when Fsref = 48 kHz, 5.6448 MHz when Fsref = 44.1 kHz).
Note that the DAC analog performance may be degraded by excessive clock jitter on the MCLK input. Therefore, care must
be taken to keep jitter on this clock to a minimum.
DAC Digital Volume Control
The DAC has a digital volume control block, which implements programmable gain. The volume level can be varied from
0 dB to –63.5 dB in 0.5 dB steps. In addition, there is an independent mute bit for each channel. The volume level of both
channels can also be changed simultaneously by the master volume control. The gain is implemented with a soft-stepping
algorithm, which only changes the actual volume by one step per input sample, either up or down, until the desired volume
is reached. The rate of soft-stepping can be slowed to one step per two input samples through bit D1 of control register
04H/Page2.
Because of soft-stepping, the host does not know when the DAC has been actually muted. This may be important if the
host wishes to mute the DAC before making a significant change, such as changing sample rates. In order to help with this
situation, the ’DAC26 provides a flag back to the host via a read-only register bit (D2D3 of control register 04H/Page2)
that alerts the host when the part has completed the soft-stepping and the actual volume has reached the desired volume
level. The soft-stepping feature can be disabled by programming D14=1 in register 1DH in Page02. If soft-stepping is
enabled, the MCLK signal to the device should not be changed until the DAC power-down flag is set. When this flag is set,
the internal soft-stepping process and power-down sequence is complete, and the MCLK can be stopped if desired.
相關PDF資料
PDF描述
TLV320AIC25I Layout and Grounding Guidelines for TLV320AIC2x
TLV320AIC11PFB Labels; External Height:0.275"; External Width:1"; Label Material:Metalized Polyester
TLV320AIC27PFB STEREO AUDIO CODEC
TMPR28051-3-SL5 Paired Cable; Number of Conductors:12; Conductor Size AWG:24; No. Strands x Strand Size:7 x 32; Jacket Material:Polyolefin; Number of Pairs:6; Impedance:100ohm; Voltage Nom.:300V RoHS Compliant: Yes
TMPR28051 TMPR28051 STS-1/AU-3 (STM-0) Mapper Device Advisory for Version 5 of the Device
相關代理商/技術參數
參數描述
TLV320AIC21IPFB 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC21IPFBG4 功能描述:接口—CODEC 64 x 18 3.3-V Synch FIFO Memory RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC21IPFBR 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC21IPFBRG4 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC22 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL VOIP CODEC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*