- 您現在的位置：買賣IC網 > PDF目錄371187 > TLV320AIC21I (Texas Instruments, Inc.) Layout and Grounding Guidelines for TLV320AIC2x PDF資料下載
參數資料
| 型號： | TLV320AIC21I |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Layout and Grounding Guidelines for TLV320AIC2x |
| 中文描述： | 為TLV320AIC2x布局和接地指南 |
| 文件頁數： | 24/46頁 |
| 文件大?。?/td> | 452K |
| 代理商： | TLV320AIC21I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
SLAS428 AUGUST 2004
www.ti.com
24
SPI DIGITAL INTERFACE
All ’DAC26 control registers are programmed through a standard SPI bus. The SPI allows full-duplex, synchronous, serial
communication between a host processor (the master) and peripheral devices (slaves). The SPI master generates the
synchronizing clock and initiates transmissions. The SPI slave devices depend on a master to start and synchronize
transmissions.
A transmission begins when initiated by a master SPI. The byte from the master SPI begins shifting in on the slave SPIDIN
(MOSI) pin under the control of the master serial clock. As the byte shifts in on the SPIDIN pin, a byte shifts out on the
SPIDOUT (MISO) pin to the master shift register.
The idle state of the serial clock for the ’DAC26 is low, which corresponds to a clock polarity setting of 0 (typical
microprocessor SPI control bit CPOL = 0). The ’DAC26 interface is designed so that with a clock phase bit setting of 1
(typical microprocessor SPI control bit CPHA = 1), the master begins driving its MOSI pin and the slave begins driving its
SPIDOUT pin on the first serial clock edge. The SS pin can remain low between transmissions; however, the ’DAC26 only
interprets command words which are transmitted after the falling edge of SS.
Hardware Reset
The device requires a low-to-high pulse on RESET after power up for correct operation. A hardware reset pulse initializes
all the internal registers, counters, and logic.
Hardware Power Down
By default the PWD pin is configured as a hardware power-down (active low) signal. The device powers down all the internal
circuitry to save power. All the register contents are maintained. Some counters maintain their value.
相關PDF資料 |
PDF描述 |
|---|---|
| TLV320AIC25I | Layout and Grounding Guidelines for TLV320AIC2x |
| TLV320AIC11PFB | Labels; External Height:0.275"; External Width:1"; Label Material:Metalized Polyester |
| TLV320AIC27PFB | STEREO AUDIO CODEC |
| TMPR28051-3-SL5 | Paired Cable; Number of Conductors:12; Conductor Size AWG:24; No. Strands x Strand Size:7 x 32; Jacket Material:Polyolefin; Number of Pairs:6; Impedance:100ohm; Voltage Nom.:300V RoHS Compliant: Yes |
| TMPR28051 | TMPR28051 STS-1/AU-3 (STM-0) Mapper Device Advisory for Version 5 of the Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV320AIC21IPFB | 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC21IPFBG4 | 功能描述:接口—CODEC 64 x 18 3.3-V Synch FIFO Memory RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC21IPFBR | 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC21IPFBRG4 | 功能描述:接口—CODEC Low Power Low IOVdd Dual Channel RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLV320AIC22 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL VOIP CODEC |
發布緊急采購，3分鐘左右您將得到回復。