參數資料
型號： TMS320C6205GHK200
廠商： Texas Instruments
文件頁數： 24/73頁
文件大小： 0K
描述： IC DSP FIXED POINT HP 288-BGA
標準包裝： 90
系列： TMS320C62x
類型： 定點
接口： McBSP，PCI
時鐘速率： 200MHz
非易失內存： 外部
芯片上RAM： 128kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.50V
工作溫度： 0°C ~ 90°C
安裝類型： 表面貼裝
封裝/外殼： 288-LFBGA
供應商設備封裝： 288-BGA Microstar（16x16）
包裝： 托盤
其它名稱： 296-12673
TMS320C6205
FIXEDPOINT DIGITAL SIGNAL PROCESSOR
SPRS106G OCTOBER 1999 REVISED JULY 2006
30
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
triggering, wake-up, and effects
The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 1510)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 8 and described in Table 5.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
“writing” to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the TMS320C6000 CPU
and Instruction Set Reference Guide (literature number SPRU189).
31
16
15
14
13
12
11
10
9
8
Reserved
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
PD3
PD2
PD1
R/W-0
7
0
Legend: R/Wx = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 8. PWRD Field of the CSR Register
Power-down mode PD1 takes effect eight to nine clock cycles after the instruction that sets the PWRD bits in the
CSR.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where PD1
took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed first,
then the program execution returns to the instruction where PD1 took effect. The GIE bit in CSR and the NMIE
bit in the interrupt enable register (IER) must also be set in order for the interrupt service routine to execute;
otherwise, execution returns to the instruction where PD1 took effect upon PD1 mode termination by an enabled
interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 5 summarizes all the power-down modes.
相關PDF資料
PDF描述
EBM18DRMH-S288 CONN EDGECARD 36POS .156 EXTEND
ACM36DRSN CONN EDGECARD 72POS DIP .156 SLD
GEM24DSEN-S13 CONN EDGECARD 48POS .156 EXTEND
ACM36DRSH CONN EDGECARD 72POS DIP .156 SLD
171-050-202L031 CONN DB50 FEMALE SOLDER CUP TIN
相關代理商/技術參數
參數描述
TMS320C6205GHKA200 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6205GJC100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6205GJL100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6205GLS100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6205GLW100 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*