參數資料
型號： TMS320F206PZL
元件分類： 數字信號處理
英文描述： 16-Bit Digital Signal Processor
中文描述： 16位數字信號處理器
文件頁數： 4/57頁
文件大?。?/td> 793K
代理商： TMS320F206PZL
TMS320F206
DIGITAL SIGNAL PROCESSOR
SPRS050A – NOVEMBER 1996 – REVISED APRIL 1998
4
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
TMS320F206 Terminal Functions (Continued)
TERMINAL
NAME
TYPE
DESCRIPTION
NO.
MEMORY CONTROL SIGNALS (CONTINUED)
WE
44
O/Z
Write enable. The falling edge of WE indicates that the device is driving the external data bus (D15–D0). Data
can be latched by an external device on the rising edge of WE. WE is active on all external program, data, and
I/O writes. WE goes into the high-impedance state when OFF is active low.
STRB
46
O/Z
Strobe signal. STRB is always high unless asserted low to indicate an external bus cycle. STRB goes into the
high-impedance state when OFF is active low.
MULTI-PROCESSING SIGNALS
BR
43
O/Z
Bus-request signal. BR is asserted when a global data-memory access is initiated. BR goes into the
high-impedance state when OFF is active low.
HOLDA
6
O/Z
Hold-acknowledge signal. HOLDA indicates to the external circuitry that the processor is in a hold state and
that the address, data, and memory control lines are in the high-impedance state so that they are available to
the external circuitry for access of local memory. HOLDA goes into the high-impedance state when OFF is
active low.
XF
98
O/Z
External flag output (latched software-programmable signal). XF is used for signalling other processors in
multiprocessing configurations or as a general-purpose output pin. XF goes into the high-impedance state
when OFF is active low.
BIO
99
I
Branch control input. When polled by the BIOZ instruction, if BIO is low, the TMS320F206 executes a branch.
IO0
IO1
IO2
IO3
96
97
8
9
I/O/Z
Software-controlled input/output pins by way of the asynchronous serial-port control register (ASPCR). At
reset, IO0–IO3 are configured as inputs. These pins can be used as general-purpose input/output pins or as
handshake control for the UART. IO0–IO3 go into the high-impedance state when OFF is active low.
IO0 also functions as a frame-sync output when the synchronous serial port (SSP) is used in multichannel
mode.
INITIALIZATION, INTERRUPTS, AND RESET OPERATIONS
RS
100
I
Reset input. RS causes the TMS320F206 to terminate execution and forces the program counter to zero.
When RS is brought high, execution begins at location 0 of program memory after 16 cycles. RS affects various
registers and status bits.
TEST
1
I
Reserved input pin. TEST is connected to VSS for normal operation.
Microprocessor/microcomputer-mode-select pin. If MP/MC is low, the on-chip flash memory is mapped into
program space. When MP/MC is high, the device accesses off-chip memory. This pin is only sampled at reset,
and its value is latched into bit 0 of the PMST register.
MP/MC
2
I
NMI
17
I
Nonmaskable interrupt. NMI is an external interrupt that cannot be masked by way of the interrupt-mode bit
(INTM) or the interrupt mask register (IMR). When NMI is activated, the processor traps to the appropriate
vector location. If NMI is not used, it should be pulled high.
HOLD/INT1
18
I
HOLD and INT1 share the same pin. Both are treated as interrupt signals. If the MODE bit is 0 in the
interrupt-control register (ICR), hold logic can be implemented in combination with the IDLE instruction in
software. At reset, the MODE bit in ICR is zero, enabling the HOLD mode for the pin.
INT2
INT3
19
20
I
External user interrupts. INT2 and INT3 are prioritized and maskable by the IMR and the INTM. INT2 and INT3
can be polled and reset by way of the interrupt flag register (IFR).
OSCILLATOR, PLL, AND TIMER SIGNALS
TOUT
92
O/Z
Timer output. TOUT signals a pulse when the on-chip timer counts down past zero. The pulse is one
CLKOUT1-cycle wide. TOUT goes into the high-impedance state when OFF is active low.
CLKOUT1
15
O/Z
Master clock output signal. The CLKOUT1 signal cycles at the machine-cycle rate of the CPU. The internal
machine cycle is bounded by the rising edges of CLKOUT1. CLKOUT1 goes into the high-impedance state
when OFF is active low.
CLKIN/X2
X1
12
13
I
O
Input clock. CLKIN/X2 is the input clock to the device. As CLKIN, the pin operates as the external oscillator
clock input, and as X2, the pin operates as the internal oscillator input with X1 being the internal oscillator
output.
I = input, O = output, Z = high impedance, PWR = power, GND = ground
相關PDF資料
PDF描述
TMS320F240PQA 16-Bit Microcontroller
TMS320C240PQL 16-Bit Microcontroller
TMS320C240PQQ 16-Bit Microcontroller
TMS320F240PQL 16-Bit Microcontroller
TMS320F240PQQ 16-Bit Microcontroller
相關代理商/技術參數
參數描述
TMS320F240PQ 功能描述:數字信號處理器和控制器 - DSP, DSC 32B Dig Sig Cntrllr w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F240PQA 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F240PQG4 功能描述:數字信號處理器和控制器 - DSP, DSC CMOS 320F240 BQFP TMS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F240PQS 功能描述:數字信號處理器和控制器 - DSP, DSC 32B Dig Sig Cntrllr w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F241FN 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*