參數資料
型號: TPS65023QRHARQ1
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: POWER SUPPLY SUPPORT CKT, PQCC40
封裝: 6 X 6 MM, GREEN, PLASTIC, MO-220VJJD-2, VQFN-40
文件頁數: 14/54頁
文件大?。?/td> 1546K
代理商: TPS65023QRHARQ1
www.ti.com
SLVS927C – MARCH 2009 – REVISED MAY 2010
DETAILED DESCRIPTION
VRTC Output and Operation With or Without Backup Battery
The VRTC pin is an always-on output, intended to supply up to 30 mA to a permanently required rail (i.e., for a
real-time clock). The TPS65023 asserts the RESPWRON signal if VRTC drops below 2.4 V. VRTC is selected
from a priority scheme based on the VSYSIN and VBACKUP inputs.
When the voltage at the VSYSIN pin exceeds 2.65 V, VRTC connects to the VSYSIN input via a PMOS switch
and all other paths to VRTC are disabled. The PMOS switch drops a maximum of 375 mV at 30 mA, which
should be considered when using VRTC. VSYSIN can be connected to any voltage source with the appropriate
input voltage, including VCC or, if set to 3.3-V output, DCDC2 or DCDC3. When VSYSIN falls below 2.65 V or
shorts to ground, the PMOS switch connecting VRTC and VSYSIN opens and VRTC then connects to either
VBACKUP or the output of a dedicated 3-V/30-mA LDO. Texas Instruments recommends connecting VSYSIN to
VCC or ground - VCC if a non-replaceable primary cell is connected to VBACKUP and ground if the VRTC
output will float.
If the PMOS switch between VSYSIN and VRTC is open and VBACKUP exceeds 2.65 V, VRTC connects to
VBACKUP via a PMOS switch. The PMOS switch drops a maximum of 375 mV at 30 mA, which should be
considered if using VRTC. A typical application may connect VBACKUP to a primary Li button cell, but any
battery that provides a voltage between 2.65 V and 6 V (i.e. a single Li-Ion cell or a single boosted NiMH battery)
is acceptable, to supply the VRTC output. In systems with no backup battery, the VBACKUP pin should be
connected to GND.
If the switches between VRTC and VSYSIN or VBACKUP are open, the dedicated 3-V/30-mA LDO, driven from
VCC, connects to VRTC. This LDO is disabled if the voltage at the VSYSIN input exceeds 2.65 V.
Inside TPS65023 there is a switch (Vmax switch) which selects the higher voltage between VCC and VBACKUP.
This is used as the supply voltage for some basic functions. The functions powered from the output of the Vmax
switch are:
INT output
RESPWRON output
HOT_RESET input
LOW_BAT output
PWRFAIL output
Enable pins for dc-dc converters, LDO1 and LDO2
Undervoltage lockout comparator (UVLO)
Reference system with low frequency timing oscillators
LOW_BAT and PWRFAIL comparators
The main 2.25-MHz oscillator, and the I2C interface are only powered from VCC.
Copyright 2009–2010, Texas Instruments Incorporated
21
Product Folder Link(s): TPS65023-Q1
相關PDF資料
PDF描述
TPS65040ZQER 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA71
TPS650531IRGERQ1 POWER SUPPLY SUPPORT CKT, PQCC24
TPS650532RGET 5-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24
TPS650531RGER 5-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24
TPS65055RSMR 1.8 A DUAL SWITCHING CONTROLLER, 2475 kHz SWITCHING FREQ-MAX, PQCC32
相關代理商/技術參數
參數描述
TPS65023QRSBRQ1 功能描述:電池管理 Auto Cat 6Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65023RSBG4 制造商:Texas Instruments 功能描述:
TPS65023RSBR 功能描述:電池管理 6Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65023RSBRG4 功能描述:電池管理 6Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
TPS65023RSBT 功能描述:電池管理 6-Channel Power Management IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel